Contact Us

STM32F207VFT6

Brand: ST
ST STM32F207VFT6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM32F207VFT6 — MCU & Embedded Processors | Superb Automation

STM32F207VFT6

ST — MCU & Embedded Processors

Product Overview

The STM32F207VFT6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM32F207VFT6: 768 Kbyte, LQFP100 body

STM32F207VFT6 is a member of the STM32F205 and STM32F207 performance line described by DS6329 Rev 18. The order code fixes 768 Kbytes of Flash, 128 Kbytes of SRAM, the LQFP100 body at 14 x 14 mm with 100 pins, 82 general purpose I/O and 16 external channels on each of the 12 bit converters, and the core runs at up to 120 MHz from a 1.8 to 3.6 V supply.

Order code and memory

Order codeSTM32F207VFT6
Program Flash768 Kbytes
SRAM128 Kbytes
PackageLQFP100, 14 x 14 mm, 100 pins
Maximum general purpose I/O82
Analog input channels16 external channels per converter
Digital to analog converternot present
External memory controllerbank 1 or bank 2 only on this 100 pin body, bank 1 multiplexed NOR or PSRAM on NE1, bank 2 a 16 or 8 bit NAND on NCE2, no interrupt line because port G is not bonded
Supply voltage1.8 to 3.6 V
Maximum CPU clock120 MHz
Temperature gradesuffix 6, minus 40 to plus 85 C ambient, 105 C junction
DatasheetDS6329 Rev 18

Peripheral and electrical parameters

CoreARM Cortex-M3 at up to 120 MHz with the adaptive real time accelerator, 1.25 DMIPS per MHz, 150 DMIPS, a memory protection unit and single cycle multiply and divide
Clock sources4 to 26 MHz high speed external crystal, 16 MHz factory trimmed internal RC, 32.768 kHz low speed internal and external sources, a main PLL and a separate audio PLL for the I2S blocks
Timerstwo advanced-control 16 bit timers with complementary outputs and dead time, four full featured general purpose timers of which TIM2 and TIM5 are 32 bit, six further general purpose 16 bit timers, two basic timers, the independent and window watchdogs, the SysTick counter and the RTC, which is the seventeen the cover counts
Serial interfacesthree SPI blocks two of which mux to I2S, three I2C blocks, four USARTs and two UARTs, two CAN 2.0B active controllers and one SDIO interface
DMAtwo DMA controllers with eight streams each and a FIFO per stream, sixteen streams in total, with circular buffer support
ADCthree 12 bit successive approximation converters with a 0.5 microsecond conversion time, each sharing up to 16 external channels, up to 24 channels across the three on the larger bodies and up to 6 Msps in triple interleaved mode
DACtwo 12 bit channels with output buffers
Ethernet10/100 MAC with dedicated DMA, MII or RMII, IEEE 1588 timestamping
Camera interfaceparallel camera interface present in the line, but the usable data width on this body follows the pin table and is limited to the low byte
Cryptographic accelerationnot present on this part
Programmable voltage detectorprogrammable voltage detector with selectable thresholds, plus power on reset, power down reset and brownout reset
Debug portserial wire debug and JTAG, with the trace port sharing low order port bits
Backup domainthe VBAT domain keeps the RTC, the 4 Kbytes of backup SRAM and the backup registers alive with the main rail off
Flash endurance and retention10 kcycles at minus 40 to plus 85 C and 1 kcycle at 105 C, with 30 years of retention at 85 C after one kcycle, 20 years at 55 C after 10 kcycles and 10 years at 105 C
Thermal resistance junction to ambient46 C/W on this package
Input tolerancealmost all inputs 5 V tolerant, with fast I/O toggling to 60 MHz on the larger bodies
USBone OTG full speed port on the device pins and one OTG high speed port that needs an external ULPI PHY
Statusproduction data per the datasheet cover

Points to check before this part goes on a BOM

This is the middle density of the 100 pin STM32F207 range, between the 512 Kbyte and 1 Mbyte codes, and all three share the same 82 general purpose pins and the same reduced memory controller. The choice between them is memory and price only, which makes the three a useful sourcing set when one density is on allocation.

The reduced memory controller is the constraint to understand on this body: bank 1 with the NE1 chip select in multiplexed NOR or PSRAM mode, or bank 2 as a 16 or 8 bit NAND on NCE2, and no ready or interrupt line because port G is not bonded. A multiplexed PSRAM on bank 1 is the usual external memory on this package, and it works well as a frame or log buffer.

Ethernet with RMII costs about nine pins including the reference clock. With 82 pins and a camera interface competing for port C and port D, a board that wants both RMII and external memory should plan the pin assignment around one of them, typically placing the camera on the low byte so that the upper port C bits stay with the PHY.

The 1.8 to 3.6 V supply range is wider than the STM32F1 lines, which matters on a board that runs from a single lithium cell or from a 3 V rail with no regulator headroom. At 1.8 V the core runs at reduced speed and the USB ports need the higher rail, so the operating point has to be checked against the voltage and frequency table rather than assumed.

The 46 C/W of the LQFP100 gives about 430 mW at 85 C ambient, and this density is often run with a network stack plus the memory controller, which keeps both the core and the I/O busy. On a board that drives an external PSRAM at 60 MHz, the I/O current on the address and data lines is a measurable share of that budget and should be added to the core figure.

Where this order code fits

It is 768 Kbytes with Ethernet in the 100 pin body, for networked boards that want a 14 x 14 mm package and do not need the 1 Mbyte density. Boards comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the Pin to Pin Cross Reference page. Both list the figures that have to match before a substitute goes on a BOM.

Questions buyers ask

What memory controller functions work on this package? Bank 1 in multiplexed NOR or PSRAM mode on NE1, or bank 2 as a 16 or 8 bit NAND on NCE2. There is no ready or interrupt line because port G is not bonded, and only one bank is usable at a time.

Does this part have the camera interface? The silicon carries it, but this body does not bond enough pins for a full width sensor. It is usable with the low byte, which covers 8 bit sensors. A 10, 12 or 14 bit sensor needs the 144 pin or 176 pin body.

How does this compare with STM32F207VGT6? The same package, pinout and SRAM, with 768 Kbytes instead of 1 Mbyte of Flash. Firmware that fits runs unchanged, and the two are interchangeable on a board.

SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the Strategic Sourcing page sets out the checks that keep a substitute from failing on the bench.