STM32F207IGH6
Product Specifications
STM32F207IGH6
ST — MCU & Embedded Processors
Product Overview
The STM32F207IGH6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
- Integrated flash memory and SRAM for efficient code execution
- Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
- Low-power modes for battery-operated and energy-sensitive applications
- Hardware security features: secure boot, crypto accelerator, TRNG
- Extensive development ecosystem with IDE, HAL, and RTOS support
Key Specifications
| Core | — |
| Max Frequency | MHz |
| Flash | KB |
| SRAM | KB |
| GPIO | — |
| ADC | bits |
| Interfaces | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
STM32F207IGH6: 1024 Kbyte, UFBGA176 body
STM32F207IGH6 is a member of the STM32F205 and STM32F207 performance line described by DS6329 Rev 18. The order code fixes 1024 Kbytes of Flash, 128 Kbytes of SRAM, the UFBGA176 body at 10 x 10 mm with 176 pins, 140 general purpose I/O and 16 external channels on each of the 12 bit converters, and the core runs at up to 120 MHz from a 1.8 to 3.6 V supply.
Order code and memory
| Order code | STM32F207IGH6 |
| Program Flash | 1024 Kbytes |
| SRAM | 128 Kbytes |
| Package | UFBGA176, 10 x 10 mm, 176 pins |
| Maximum general purpose I/O | 140 |
| Analog input channels | 16 external channels per converter |
| Digital to analog converter | not present |
| External memory controller | full flexible static memory controller with four chip selects on this 176 ball body |
| Supply voltage | 1.8 to 3.6 V |
| Maximum CPU clock | 120 MHz |
| Temperature grade | suffix 6, minus 40 to plus 85 C ambient, 105 C junction |
| Datasheet | DS6329 Rev 18 |
Peripheral and electrical parameters
| Core | ARM Cortex-M3 at up to 120 MHz with the adaptive real time accelerator, 1.25 DMIPS per MHz, 150 DMIPS, a memory protection unit and single cycle multiply and divide |
| Clock sources | 4 to 26 MHz high speed external crystal, 16 MHz factory trimmed internal RC, 32.768 kHz low speed internal and external sources, a main PLL and a separate audio PLL for the I2S blocks |
| Timers | two advanced-control 16 bit timers with complementary outputs and dead time, four full featured general purpose timers of which TIM2 and TIM5 are 32 bit, six further general purpose 16 bit timers, two basic timers, the independent and window watchdogs, the SysTick counter and the RTC, which is the seventeen the cover counts |
| Serial interfaces | three SPI blocks two of which mux to I2S, three I2C blocks, four USARTs and two UARTs, two CAN 2.0B active controllers and one SDIO interface |
| DMA | two DMA controllers with eight streams each and a FIFO per stream, sixteen streams in total, with circular buffer support |
| ADC | three 12 bit successive approximation converters with a 0.5 microsecond conversion time, each sharing up to 16 external channels, up to 24 channels across the three on the larger bodies and up to 6 Msps in triple interleaved mode |
| DAC | two 12 bit channels with output buffers |
| Ethernet | 10/100 MAC with dedicated DMA, MII or RMII, IEEE 1588 timestamping |
| Camera interface | parallel camera interface, 8 to 14 bit, with its own DMA |
| Cryptographic acceleration | not present on this part |
| Programmable voltage detector | programmable voltage detector with selectable thresholds, plus power on reset, power down reset and brownout reset |
| Debug port | serial wire debug and JTAG, with the trace port sharing low order port bits |
| Backup domain | the VBAT domain keeps the RTC, the 4 Kbytes of backup SRAM and the backup registers alive with the main rail off |
| Flash endurance and retention | 10 kcycles at minus 40 to plus 85 C and 1 kcycle at 105 C, with 30 years of retention at 85 C after one kcycle, 20 years at 55 C after 10 kcycles and 10 years at 105 C |
| Thermal resistance junction to ambient | 39 C/W on this package |
| Input tolerance | almost all inputs 5 V tolerant, with fast I/O toggling to 60 MHz on the larger bodies |
| USB | one OTG full speed port on the device pins and one OTG high speed port that needs an external ULPI PHY |
| Status | production data per the datasheet cover |
Points to check before this part goes on a BOM
The H in the order code is the UFBGA176 package at 0.5 mm pitch, and it is the reason this part exists at 10 x 10 mm with 140 pins. The same 176 pins in LQFP176 take 24 x 24 mm. For a board with a camera, an Ethernet PHY, an external memory bus and three serial ports, the ball grid is the only way to keep the footprint small, at the cost of needing X-ray inspection on the assembly line.
The 10/100 MAC on this device has its own DMA, so frame traffic does not pass through the two general purpose DMA controllers and does not compete with the converter or the serial ports. It supports MII and RMII, and it carries IEEE 1588 timestamping, which is what makes it usable for industrial synchronization rather than only for a data link. The PHY is external in every case, and RMII halves the pin count against MII.
The camera interface takes 8, 10, 12 or 14 bit parallel data with its own DMA channel, which is the configuration used for machine vision sensors and for some thermal modules. It shares pins with the memory controller and with port E and port F, so a board that uses both the camera and a 16 bit external memory bus has to take the pin table through the alternate function column rather than assuming the functions coexist.
One hundred and forty general purpose pins is more than most boards use, and the surplus is what allows this part to carry an external memory bus, an LCD parallel interface in 8080 or 6800 mode, two CAN channels and a full set of serial ports at the same time. The board level consequence is a large fanout and a power delivery problem: 140 switching outputs at 60 MHz need more decoupling than a 64 pin part, not the same number.
The UFBGA176 is rated 39 C/W, close to the LQFP176 figure, so at 85 C ambient the dissipation budget is about 510 mW. The 1 Mbyte of Flash at 120 MHz with the ART accelerator is the configuration that keeps the core at zero wait states for most code, and it is also the configuration that draws the most current, so a board in this package should budget the core at the full 120 MHz and then check the thermal margin.
Where this order code fits
It is the top of the STM32F205 and F207 range, 1 Mbyte of Flash and 140 general purpose pins in a 10 x 10 mm UFBGA176, for equipment that needs Ethernet, a camera and an external memory bus at the same time. Boards comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the Pin to Pin Cross Reference page. Both list the figures that have to match before a substitute goes on a BOM.
Questions buyers ask
Does this part need an external PHY for Ethernet? Yes. The device contains the MAC only, with MII and RMII interfaces. A PHY and its magnetics are external, and RMII reduces the pin count from about 16 to about 9 against MII.
Is the LQFP176 version of this part available? Yes, as STM32F207ZGT6 in the 144 pin LQFP and STM32F207IGT6 in the 176 pin LQFP, the latter at 24 x 24 mm. The UFBGA176 code here is the same silicon in a 10 x 10 mm ball grid.
How many chip selects does the memory controller provide? Four, all bonded on this package. That is enough for a NOR, a NAND, an SRAM and one spare device on the same bus, with separate timing registers per bank.
SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.