Contact Us

STM32F107RCT6

Brand: ST
ST STM32F107RCT6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM32F107RCT6 — MCU & Embedded Processors | Superb Automation

STM32F107RCT6

ST — MCU & Embedded Processors

Product Overview

The STM32F107RCT6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM32F107RCT6: 256 Kbytes of Flash and Ethernet in 64 Pins

STM32F107RCT6 is the largest density of the connectivity line in the 64 pin LQFP body: 256 Kbytes of flash, 64 Kbytes of SRAM, a 10/100 Ethernet MAC with its own 4 Kbyte buffer memory, two CAN controllers, USB OTG and a 72 MHz Cortex-M3 core, on 51 I/O pins. The C in the code is the 256 Kbyte density and the R is the 64 pin body. It is the smallest package in the range that still carries Ethernet, which makes it the part to look at when a gateway has to fit inside a DIN rail enclosure.

51 pins with an RMII port attached

An RMII link takes nine signals, the two CAN buses take four, USB takes two plus the ID line, the crystal takes two and the debug port two, which leaves about 30 pins for everything else on the board. That is enough for two USARTs, an SPI display, a handful of digital inputs and a relay driver, and not enough for an external memory bus. The 64 pin connectivity part is therefore a network node rather than a controller, and the 100 pin version exists for boards that need both the network and a wide I/O count.

Values at a glance

ParameterValueNote
Core and clockCortex-M3, 72 MHz1.25 DMIPS/MHz, 12 channel DMA, trace macrocell
Flash, SRAM256 Kbytes, 64 Kbytes128 Kbyte RB code in the same body
PackageLQFP64, 10 by 10 mmPin count is the limit on the peripheral mix
I/O51 pinsAlmost all 5 V tolerant
Ethernet10/100 MAC, RMII or MII4 Kbytes dedicated SRAM, IEEE 1588 hardware support
CAN2 controllers, 2.0B active512 bytes dedicated SRAM
USB2.0 full speed device, host, OTGOn chip PHY, 1.25 Kbytes dedicated SRAM
Analog2 ADC 12 bit 16 channels; 2 DAC2 MSPS interleaved, 0 to 3.6 V range

256 Kbytes is what a network stack actually needs

A small TCP/IP stack with an HTTP server, a Modbus TCP layer and the application typically lands between 90 and 140 Kbytes of flash, which fits comfortably in 256 and does not fit in the 128 Kbyte RB code once a bootloader and a second protocol are added. The SRAM side is the tighter constraint: 64 Kbytes shared between the Ethernet descriptors, the receive buffers, the application and the stack, with the dedicated MAC memory absorbing only the descriptor side. A 4 Kbyte receive window and a 2 Kbyte transmit ring are a reasonable starting point, and a second socket doubles the buffers rather than the code.

Sourcing the networking part

Gateway products keep this family in steady demand, and the 64 pin Ethernet density is one of the more sought after codes because it fits the small enclosures. Availability moves between the RB and RC densities in the same body, and the difference between them is flash size alone. An alternate part check against the RB code, a lead time view that separates stock from future dates, and a vendor consolidation arrangement that bundles the PHY and the magnetics with the microcontroller are the practical levers here.

Common questions

Can the 64 pin part drive an external SRAM? No, the memory controller is not part of the connectivity line at all. External memory requires the STM32F103 high density or the STM32F205 range.

How many ADC channels are available here? 16, the same as the 100 pin body, because the analog inputs are concentrated on ports A and C which are fully bonded out on this package.

Does the Ethernet MAC need a dedicated crystal? It needs a 25 or 50 MHz reference for RMII depending on the configuration, which can come from the PHY instead of from the microcontroller, and that choice decides which part of the board carries the accuracy requirement.