Contact Us

STM32F103V8T6

Brand: ST
ST STM32F103V8T6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM32F103V8T6 — MCU & Embedded Processors | Superb Automation

STM32F103V8T6

ST — MCU & Embedded Processors

Product Overview

The STM32F103V8T6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM32F103V8T6: 64 Kbytes of Flash with 80 I/Os and 16 Analog Channels

STM32F103V8T6 is the medium density STM32F103 in the 100 pin LQFP body: 64 Kbytes of flash, 20 Kbytes of SRAM, 80 I/O pins and 16 analog channels from two 12 bit converters. It is the same silicon generation as the 48 pin C8 part that most reference boards use, but with the pins bonded out that a machine control or an instrument panel needs. Buyers compare it directly with the V-part of the high density line, and the difference is memory plus the memory controller rather than clock or pinout.

The medium density peripheral set at 100 pins

Three general purpose 16 bit timers, one advanced control timer with dead time and break input, two watchdog timers, a SysTick counter, two SPI ports, two I2C ports, three USARTs, a USB 2.0 full speed device port and one CAN 2.0B active controller. The DMA controller has seven channels. Compared with the 48 pin body the gain is pins and analog channels, not peripherals: the same peripheral list is available on the small package, which is why a project can prototype on the C8 part and move to this body with the same firmware.

Values at a glance

ParameterValueNote
Core and clockCortex-M3, 72 MHz1.25 DMIPS/MHz at 0 wait state memory access
Flash, SRAM64 Kbytes, 20 Kbytes128 Kbyte VB code in the same body
PackageLQFP100, 14 by 14 mmLFBGA100 body available for the same density
I/O80 pins16 external interrupt vectors, 5 V tolerant digital pins
ADC2 converters, 12 bit, 16 channels1 microsecond conversion, dual sample and hold
Timers3 general purpose, 1 advanced, 2 watchdogEach general timer has four compare channels and an encoder input
Communication2 SPI, 2 I2C, 3 USART, USB FS, CANSPI at 18 Mbit/s, USART with smartcard and IrDA modes
TemperatureMinus 40 to plus 85 CCode 7 extends the ambient limit to 105 C

20 Kbytes of SRAM on a 100 pin board

The 100 pin body invites an external memory or a display, and both of those eat RAM in the driver as well as pins. A TFT driver with a full frame buffer does not fit at all: a 320 by 240 pixel, 16 bit image is 150 Kbytes, seven times what the part has. The workable pattern on this density is a partial buffer of a few lines with the display refreshed from a small window, or a character display driven through a serial interface. Teams that need a frame buffer move to the high density line with the memory controller, where an external SRAM supplies the buffer instead of the on chip RAM.

Where the V8 code sits in supply terms

Demand for 100 pin medium density parts is steady but not large, so stock is thinner than for the 48 pin codes and thicker than for the low density ones. A build short of the V8 code can consider the VB code, which is the same device with 128 Kbytes of flash in the same footprint, and the swap needs no board change. Confirming that in writing is the job of a microcontroller cross reference sheet, and the purchasing route for either code is covered under one stop BOM sourcing and the drop in replacement checklist that turns a suggestion into a signed record.

Common questions

Can the 100 pin part run two CAN buses? No. The medium density line has one CAN controller. Two buses require the connectivity line STM32F105 or STM32F107, or the high density part with its single controller plus a second external device.

Is the USB port usable while the CAN bus runs? Yes, both interfaces are independent, and the shared resource is the clock tree and the pin allocation rather than the peripheral itself.

What clock accuracy does the CAN bus need? The oscillator has to hold within the tolerance the bus timing requires across temperature, which in practice means a crystal rather than the internal RC for any bus longer than a few metres.