STM32F103R6T6
Product Specifications
STM32F103R6T6
ST — MCU & Embedded Processors
Product Overview
The STM32F103R6T6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
- Integrated flash memory and SRAM for efficient code execution
- Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
- Low-power modes for battery-operated and energy-sensitive applications
- Hardware security features: secure boot, crypto accelerator, TRNG
- Extensive development ecosystem with IDE, HAL, and RTOS support
Key Specifications
| Core | — |
| Max Frequency | MHz |
| Flash | KB |
| SRAM | KB |
| GPIO | — |
| ADC | bits |
| Interfaces | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
STM32F103R6T6: 64 Pins, 51 I/Os, 32 Kbytes of Flash
STM32F103R6T6 puts the low density STM32F103 device into the 64 pin LQFP body, which adds 14 I/O pins over the 48 pin version and raises the analog channel count from 10 to 16. Flash is 32 Kbytes, SRAM is 10 Kbytes, the core is Cortex-M3 at 72 MHz, and the temperature suffix 6 is minus 40 to plus 85 C. For a board that needs more GPIO than a 48 pin part can give but does not need more code space, this is the cheapest way to gain pins without changing family.
Why the extra 14 pins matter
The 64 pin body exposes port C and the upper part of port B more completely, along with the second converter channel group. On a board that drives an eight bit parallel display, a keypad matrix and a relay bank, the 37 pins of the 48 pin part run out quickly, and every one of those pins is also competing with the SPI, I2C and USART alternate functions. Sixteen analog channels instead of ten means a thermocouple array or a multi cell voltage monitor can stay on chip instead of moving to an external multiplexer, which is usually the difference between a two layer and a four layer board.
Values at a glance
| Parameter | Value | Note |
|---|---|---|
| Core and clock | Cortex-M3, 72 MHz | 1.25 DMIPS/MHz, hardware divide |
| Flash, SRAM | 32 Kbytes, 10 Kbytes | The R8 code gives 64 Kbytes in the same package |
| Package | LQFP64, 10 by 10 mm | TFBGA64 also offered, with 15 analog channels instead of 16 |
| I/O | 51 pins | Nearly all 5 V tolerant on the digital side |
| ADC | 2 converters, 12 bit, 16 channels | 15 on the TFBGA64 body because one pin becomes VREF+ |
| Timers | 2 general purpose, 1 advanced, 2 watchdog | Advanced timer includes dead time and break input |
| Communication | 1 SPI, 1 I2C, 2 USART, USB FS, CAN | Low density peripheral set, not the medium density one |
| Temperature | Minus 40 to plus 85 C | Extended range code 7 reaches plus 105 C |
The BGA variant is not identical
The TFBGA64 body carries 5 by 5 mm of area and a 0.5 mm ball pitch, which is attractive for a small module, but one analog input is replaced by the VREF+ pin, so the channel count drops from 16 to 15 and the reference becomes externally adjustable. A board qualified on the LQFP part that moves to the BGA body changes both its analog routing and its reference arrangement, which is why the two bodies are usually treated as two separate approvals rather than one.
Buying the R6 code in a market that prefers the R8
Distributor stock tends to concentrate on the larger density codes, so the R6 is often quoted from fewer sources and with a longer date. Two practical routes exist: accept the R8 code, which is the same die with 64 Kbytes of flash in the same 64 pin footprint, or hold the R6 code and cover the build from the open market. The second route needs a documented check, so a microcontroller cross reference entry that lists R6 and R8 as one device family, a one stop BOM consolidation that keeps the two codes in one line item, and a drop in verification record are the three documents that make either route auditable.
Common questions
Can a 64 pin part replace a 48 pin part on an existing board? Not physically. The 48 pin body is 7 by 7 mm and the 64 pin body is 10 by 10 mm with a different lead span. The move only works at the board revision level.
Are all 51 I/Os usable at once? Only if the crystal, the debug port and the analog reference pins are not needed. SWD takes two pins, the crystal takes two more, and the BOOT0 pin is usually strapped, so a working count is closer to 46.
Is the USB port shared with anything? The USB pins are on PA11 and PA12 and can be remapped in software, but the transceiver is fixed to those pins unless the remap option is used. Sharing them with a CAN function is possible on some packages and needs the pin table check.