Contact Us

STM32F101VBT6

Brand: ST
ST STM32F101VBT6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM32F101VBT6 — MCU & Embedded Processors | Superb Automation

STM32F101VBT6

ST — MCU & Embedded Processors

Product Overview

The STM32F101VBT6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM32F101VBT6: 128 Kbyte, LQFP100 body

STM32F101VBT6 is a member of the STM32F101 medium density access line described by DocID13586 Rev 17. The order code fixes 128 Kbytes of Flash, 16 Kbytes of SRAM, the LQFP100 body at 14 x 14 mm with 100 pins, 80 general purpose I/O and 16 channels of the 12 bit converter, and the core runs at up to 36 MHz from a 2.0 to 3.6 V supply.

Order code and memory

Order codeSTM32F101VBT6
Program Flash128 Kbytes
SRAM16 Kbytes
PackageLQFP100, 14 x 14 mm, 100 pins
Maximum general purpose I/O80
Analog input channels16 of the 12 bit converter
Digital to analog converternot present
External memory controllernot present on this line
Supply voltage2.0 to 3.6 V
Maximum CPU clock36 MHz
Temperature gradesuffix 6, minus 40 to plus 85 C ambient, 105 C junction

Peripheral and electrical parameters

CoreARM Cortex-M3 at up to 36 MHz, 1.25 DMIPS per MHz, single cycle multiply and divide
Timersthree 16 bit general purpose timers with up to four compare channels each, plus the independent and window watchdogs and the SysTick counter
Serial interfacesthree USARTs, two SPI blocks and two I2C blocks on 48 pins and above, two USARTs, one SPI and one I2C on the 36 pin body
DMA7 channel DMA controller
ADC12 bit, 1 microsecond conversion, 10 channels on 36 and 48 pins and 16 channels on 64 and 100 pins
DACnot present on this line
Stop current14 uA typical and 180 uA maximum at 85 C from a 3.3 V supply
Standby current2 uA typical and 4 uA maximum
Internal RC accuracy8 MHz factory trimmed RC, 1.1 percent at 25 C and 2.2 percent worst case
Flash endurancenot stated in this datasheet revision
Input tolerancealmost all inputs 5 V tolerant
USBnot present, USB full speed is the STM32F102 line
Statusproduction data per the datasheet cover

Points to check before this part goes on a BOM

V is 100 pins, B is 128 Kbytes of Flash and 6 is the industrial range. On the 100 pin medium density row DocID13586 gives 16 Kbytes of SRAM, 80 general purpose I/O, 16 converter channels, three USARTs, two SPI and two I2C blocks, three general purpose timers and 7 DMA channels.

This is the largest medium density part in pin count and memory at the same time, so it is the natural home for a board that started on the 64 pin RBT6 and then grew a second connector. The code and the pin functions move across without a change, because the medium density line shares one peripheral map.

16 Kbytes of SRAM sets the buffer depth. Three USARTs at 115200 baud plus a converter stream and an SPI display still fit inside it, provided the display is written from a small staging buffer rather than a full framebuffer.

The 100 pin LQFP is rated 46 C/W, and the thermal path is the package edge and the ground plane rather than an exposed pad. With 80 I/O available, a board that drives 30 opto couplers at 10 mA each is dissipating 300 mW in the package alone, which is most of the 434 mW budget.

The backup domain from VBAT holds the RTC, the backup registers and the tamper input while the main rail is off, and the 32 kHz oscillator has a calibration register. On a board with 80 I/O the tamper input is usually wired to an enclosure switch, which is the cheapest way to notice that a cover has been opened.

Where this order code fits

It pairs 128 Kbytes of Flash with 80 pins, the combination for a board that has many signals and a modest amount of code to run them. Boards comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the Pin to Pin Cross Reference page. Both list the figures that have to match before a substitute goes on a BOM.

Questions buyers ask

How many USARTs and SPI blocks? Three USARTs, two SPI blocks and two I2C blocks on this row. The 36 pin medium density part carries two USARTs, one SPI and one I2C.

What is the maximum current per I/O? The datasheet gives sink and source current limits per pin and a total for the package, and the total is the figure that decides a board with many LEDs. The 434 mW dissipation budget at 85 C ambient includes all of that I/O current.

Does it support an external crystal? Yes, a 4 to 16 MHz crystal oscillator plus a 32 kHz oscillator for the RTC with calibration, and there is an 8 MHz factory trimmed RC for boards that do not need a crystal.

SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the One Stop BOM Sourcing page sets out the checks that keep a substitute from failing on the bench.

TR and xxx in the options field describe packing and programming, and without them the code is a tray device. Before a purchase order the package current budget is worth a second look: at 46 C/W the 100 pin body allows about 434 mW inside the 20 C junction margin at 85 C ambient, and 80 I/O driving opto couplers at 10 mA each would use most of it. The alternative is to move the load drivers off the microcontroller, which also shortens the harness and removes the ground bounce that many simultaneous outputs create on a 10 x 10 mm body.