STM32F100VET6B
Product Specifications
STM32F100VET6B
ST — MCU & Embedded Processors
Product Overview
The STM32F100VET6B from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
- Integrated flash memory and SRAM for efficient code execution
- Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
- Low-power modes for battery-operated and energy-sensitive applications
- Hardware security features: secure boot, crypto accelerator, TRNG
- Extensive development ecosystem with IDE, HAL, and RTOS support
Key Specifications
| Core | — |
| Max Frequency | MHz |
| Flash | KB |
| SRAM | KB |
| GPIO | — |
| ADC | bits |
| Interfaces | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
STM32F100VET6B: 512 Kbyte, LQFP100 body
STM32F100VET6B is a member of the STM32F100 value line high density described by DS5944 Rev 11. The order code fixes 512 Kbytes of Flash, 32 Kbytes of SRAM, the LQFP100 body at 14 x 14 mm with 100 pins, 80 general purpose I/O and 16 channels of the 12 bit converter, and the core runs at up to 24 MHz from a 2.0 to 3.6 V supply.
Order code and memory
| Order code | STM32F100VET6B |
| Program Flash | 512 Kbytes |
| SRAM | 32 Kbytes |
| Package | LQFP100, 14 x 14 mm, 100 pins |
| Maximum general purpose I/O | 80 |
| Analog input channels | 16 of the 12 bit converter |
| Digital to analog converter | 2 channels of 12 bits |
| External memory controller | flexible static memory controller, bank 1 only on this body, multiplexed NOR and PSRAM |
| Supply voltage | 2.0 to 3.6 V |
| Maximum CPU clock | 24 MHz |
| Temperature grade | suffix 6, minus 40 to plus 85 C ambient, 105 C junction |
| Datasheet | DS5944 Rev 11 |
Peripheral and electrical parameters
| Core | ARM Cortex-M3 at up to 24 MHz, 1.25 DMIPS per MHz, single cycle multiply and divide |
| Clock sources | 8 MHz factory trimmed internal RC, PLL up to the 24 MHz core clock, external crystal on the high speed oscillator |
| Timers | one advanced-control 16 bit timer with four channels and complementary outputs, ten general-purpose 16 bit timers and two basic timers, which with the two watchdogs is the sixteen the cover counts |
| Serial interfaces | three SPI blocks, two I2C blocks, three USARTs and two UARTs, plus one HDMI CEC channel |
| DMA | 12 channel DMA across two controllers |
| ADC | 12 bit successive approximation, 16 channels, conversion range 0 to 3.6 V |
| DAC | 2 channels of 12 bits with output buffers |
| Programmable voltage detector | eight falling thresholds from 2.00 V to 2.88 V nominal, each with a rising edge about 100 mV higher |
| Debug port | serial wire debug on two pins and JTAG on five, with the trace port sharing low order port bits |
| Backup domain | VBAT domain keeps the RTC, the backup registers and the tamper input alive with the main rail off |
| Flash endurance and retention | 10 kcycles at minus 40 to plus 85 C, 1 kcycle at 105 C, 30 years of retention at 85 C after one kcycle and 10 years at 105 C |
| Thermal resistance junction to ambient | 40 C/W on this package |
| Input tolerance | almost all inputs 5 V tolerant |
| USB | not present, USB full speed is the STM32F102 line |
| Status | production data per the datasheet cover |
Points to check before this part goes on a BOM
512 Kbytes of Flash is the top of the value line, and it changes what the part is used for: two application slots of 256 Kbytes, a bootloader with a recovery image, or a font and a graphics library that would not fit on a 256 Kbyte code. The 32 Kbytes of SRAM is the same as the 384 Kbyte code, so the memory increase is entirely program space and not working space.
The external memory controller on this 100 pin body is bank 1 only, driving a multiplexed NOR or PSRAM device. With 512 Kbytes of program Flash the case for external memory is usually a display buffer or a data buffer, and PSRAM on bank 1 is the arrangement the package supports. A board that needs NAND or two independent chip selects has to go to the 144 pin body, which is a different footprint and a different board.
The trailing B is an internal code after the temperature digit, so the memory, the package, the pin count, the converter channels and the interface set are as listed for the unlettered 512 Kbyte code. Both are covered by DS5944 Rev 11. A buyer comparing quotes from two distributors should compare the full string, because a quote for the unlettered part is not a quote for this one even when the price is the same.
Eighty general purpose I/O with the memory bus in use is the pin budget. The bus consumes a block of port pins, the crystal takes two, the debug port takes two for serial wire and five for JTAG, and the analog pins are shared with the converter inputs and the two DAC outputs. On a 512 Kbyte part with a display on the bus, the free I/O after those allocations is what the connector assignment has to work with.
At 40 C/W the LQFP100 body allows about 500 mW from 85 C ambient to 105 C junction. A part with a bus, a display and several PWM channels is the case where the I/O current and the bus switching sit alongside the core in the same budget, and the package has the copper area to carry it provided the exposed pad is soldered into a plane with vias. A socketed or poorly soldered pad is what turns the datasheet figure into a hot part.
Flash endurance is 10 kcycles at minus 40 to plus 85 C, with 30 years of retention at 85 C after one kcycle and 10 years at 105 C. The 512 Kbyte size makes a two slot field update practical, and that is also the pattern that writes the most to Flash, so the number of updates per year has to be counted against the endurance figure. Staging the image in external PSRAM and copying it in one pass is the way to reduce the program operations per update.
The 12 channel DMA across two controllers is what keeps a 24 MHz core able to service a display bus and five asynchronous ports. The display data, the converter scan and the serial traffic all move without the core copying, and the core spends its time on protocol state machines and control arithmetic. That division is the reason a 24 MHz part can run equipment that looks like it needs a faster core.
Where this order code fits
It is the 512 Kbyte value line code with the internal letter, used where the image is large, the SRAM has to be 32 Kbytes and the board still has to fit a 100 pin 14 x 14 mm footprint. Boards comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the Obsolete Part Cross Reference Hub page. Both list the figures that have to match before a substitute goes on a BOM.
Questions buyers ask
How much SRAM does the 512 Kbyte code have? 32 Kbytes, the same as the 384 Kbyte code and 8 Kbytes more than the 256 Kbyte codes. The step from 24 to 32 Kbytes is the one that matters for a display line buffer or for a second serial port with a large buffer.
What is the difference between this and STM32F100VET6? Only the internal letter in the orderable string. Memory, package, pin count, converter channels, interface set, memory controller and clock ceiling are identical, and both are described by DS5944 Rev 11. A substitution is a procurement decision that should be recorded.
Can the memory controller drive SDRAM? No. The controller on this family handles static memories, and on the LQFP100 package bank 1 supports a multiplexed NOR or PSRAM device. SDRAM needs a different controller, which this line does not have at any density.
SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the OEM Procurement page sets out the checks that keep a substitute from failing on the bench.