Contact Us

STM32F100VCT6

Brand: ST
ST STM32F100VCT6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM32F100VCT6 — MCU & Embedded Processors | Superb Automation

STM32F100VCT6

ST — MCU & Embedded Processors

Product Overview

The STM32F100VCT6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM32F100VCT6: 256 Kbyte, LQFP100 body

STM32F100VCT6 is a member of the STM32F100 value line high density described by DS5944 Rev 11. The order code fixes 256 Kbytes of Flash, 24 Kbytes of SRAM, the LQFP100 body at 14 x 14 mm with 100 pins, 80 general purpose I/O and 16 channels of the 12 bit converter, and the core runs at up to 24 MHz from a 2.0 to 3.6 V supply.

Order code and memory

Order codeSTM32F100VCT6
Program Flash256 Kbytes
SRAM24 Kbytes
PackageLQFP100, 14 x 14 mm, 100 pins
Maximum general purpose I/O80
Analog input channels16 of the 12 bit converter
Digital to analog converter2 channels of 12 bits
External memory controllerflexible static memory controller, bank 1 only on this body, multiplexed NOR and PSRAM
Supply voltage2.0 to 3.6 V
Maximum CPU clock24 MHz
Temperature gradesuffix 6, minus 40 to plus 85 C ambient, 105 C junction
DatasheetDS5944 Rev 11

Peripheral and electrical parameters

CoreARM Cortex-M3 at up to 24 MHz, 1.25 DMIPS per MHz, single cycle multiply and divide
Clock sources8 MHz factory trimmed internal RC, PLL up to the 24 MHz core clock, external crystal on the high speed oscillator
Timersone advanced-control 16 bit timer with four channels and complementary outputs, ten general-purpose 16 bit timers and two basic timers, which with the two watchdogs is the sixteen the cover counts
Serial interfacesthree SPI blocks, two I2C blocks, three USARTs and two UARTs, plus one HDMI CEC channel
DMA12 channel DMA across two controllers
ADC12 bit successive approximation, 16 channels, conversion range 0 to 3.6 V
DAC2 channels of 12 bits with output buffers
Programmable voltage detectoreight falling thresholds from 2.00 V to 2.88 V nominal, each with a rising edge about 100 mV higher
Debug portserial wire debug on two pins and JTAG on five, with the trace port sharing low order port bits
Backup domainVBAT domain keeps the RTC, the backup registers and the tamper input alive with the main rail off
Flash endurance and retention10 kcycles at minus 40 to plus 85 C, 1 kcycle at 105 C, 30 years of retention at 85 C after one kcycle and 10 years at 105 C
Thermal resistance junction to ambient40 C/W on this package
Input tolerancealmost all inputs 5 V tolerant
USBnot present, USB full speed is the STM32F102 line
Statusproduction data per the datasheet cover

Points to check before this part goes on a BOM

Eighty general purpose I/O with a working external memory bus is the combination this code is bought for. The bus takes a share of the port pins, so the 80 is not all available to the application when bank 1 is in use: an address and data multiplexed bus plus the control signals consumes a block of port D and port E, which is why the pin table has to be read as a whole rather than counted row by row.

The 24 Kbytes of SRAM sits between the 8 Kbytes of the medium density parts and the 32 Kbytes of the larger high density codes. For a board with a display controller on the parallel bus, the internal SRAM holds the line buffers, the DMA descriptors and the serial buffers while the external device holds the frame. That split is the standard arrangement on this part and it is what keeps the 24 Kbytes from being the limit.

Three USARTs and two UARTs give five asynchronous ports, and the three SPI blocks mean a display, a serial Flash and a sensor can each have their own bus. Two I2C blocks cover an EEPROM and a monitor or a keypad controller. On a 100 pin body most of these can be brought out at the same time, which is the practical difference from the 64 pin code that carries the same silicon.

The timer set is the high density one: one advanced-control timer with complementary outputs and dead time, ten general purpose 16 bit timers and two basic timers. On equipment with several actuators that is the resource that runs out last, and the two basic timers exist so that the converter and DAC triggers do not consume a general purpose timer. A board that uses the advanced timer for a bridge and needs four independent PWM channels still has timers left for capture and for a timebase.

At 40 C/W on the LQFP100 body the junction rises 20 C above an 85 C ambient at about 500 mW. With a parallel bus running continuously the I/O contribution is significant, and the ground return path under the bus is what keeps the converter and the DAC clean. A board that puts the analog connector on the opposite side of the package from the bus pins and gives the reference pin its own capacitor is doing the cheap version of a board review.

Flash endurance is 10 kcycles at minus 40 to plus 85 C, and retention is 30 years at 85 C after one kcycle. The 256 Kbyte size supports two 128 Kbyte slots for a field update, which is the arrangement that writes the most to the program Flash. If updates are frequent, the image can be staged in the external PSRAM or a serial Flash and copied in one pass, which halves the number of program operations per update.

The 24 MHz core with 12 channel DMA is the right level for a controller that manages a display, a keypad, several serial links and a handful of PWM channels. The DMA controller moves the display data and the converter results, the core handles the state machines and the protocols, and the timer hardware produces the waveforms. Work that needs a faster core is the STM32F103 line, which shares the package family but not the pin out.

Where this order code fits

It is the plain 256 Kbyte, 100 pin high density code, used where 80 I/O and the bank 1 memory bus are needed and the unlettered string is the one on the approved vendor list. Boards comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the How to Verify a Drop in Replacement page. Both list the figures that have to match before a substitute goes on a BOM.

Questions buyers ask

How many I/O are left when the memory bus is in use? Fewer than the headline 80, because a multiplexed address and data bus plus its control signals takes a block of port pins. The pin table lists which ports carry the bus on this package, and the remainder is the number the application can use.

Can the parallel bus drive a PSRAM device? Yes, bank 1 on the LQFP100 package is intended for a multiplexed NOR or PSRAM device, which is why PSRAM is the usual choice for a frame buffer on this part. A NAND device needs the second bank and the larger package.

Is the unlettered code a different part from the lettered one? They are separate orderable strings that share a datasheet and the same memory, package and peripheral figures. The difference is an internal code, so the choice between them is a procurement and traceability decision rather than a technical one.

SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the BOM Consolidation page sets out the checks that keep a substitute from failing on the bench.