STM32F100VBT6
Product Specifications
STM32F100VBT6
ST — MCU & Embedded Processors
Product Overview
The STM32F100VBT6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
- Integrated flash memory and SRAM for efficient code execution
- Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
- Low-power modes for battery-operated and energy-sensitive applications
- Hardware security features: secure boot, crypto accelerator, TRNG
- Extensive development ecosystem with IDE, HAL, and RTOS support
Key Specifications
| Core | — |
| Max Frequency | MHz |
| Flash | KB |
| SRAM | KB |
| GPIO | — |
| ADC | bits |
| Interfaces | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
STM32F100VBT6: 128 Kbyte, LQFP100 body
STM32F100VBT6 is a member of the STM32F100 value line low and medium density described by DocID16455 Rev 9. The order code fixes 128 Kbytes of Flash, 8 Kbytes of SRAM, the LQFP100 body at 14 x 14 mm with 100 pins, 80 general purpose I/O and 16 channels of the 12 bit converter, and the core runs at up to 24 MHz from a 2.0 to 3.6 V supply.
Order code and memory
| Order code | STM32F100VBT6 |
| Program Flash | 128 Kbytes |
| SRAM | 8 Kbytes |
| Package | LQFP100, 14 x 14 mm, 100 pins |
| Maximum general purpose I/O | 80 |
| Analog input channels | 16 of the 12 bit converter |
| Digital to analog converter | 2 channels of 12 bits |
| External memory controller | not present on this body |
| Supply voltage | 2.0 to 3.6 V |
| Maximum CPU clock | 24 MHz |
| Temperature grade | suffix 6, minus 40 to plus 85 C ambient, 105 C junction |
| Datasheet | DocID16455 Rev 9 |
Peripheral and electrical parameters
| Core | ARM Cortex-M3 at up to 24 MHz, 1.25 DMIPS per MHz, single cycle multiply and divide |
| Clock sources | 8 MHz factory trimmed internal RC, PLL up to the 24 MHz core clock, external crystal range 4 to 24 MHz |
| Timers | one advanced-control 16 bit timer with four channels and complementary outputs with dead time, up to six general-purpose 16 bit timers with four compare channels each, and two basic timers that trigger the converter |
| Serial interfaces | up to two SPI blocks, two I2C blocks and three USARTs, plus one HDMI CEC channel |
| DMA | 7 channel DMA controller |
| ADC | 12 bit successive approximation, 1 microsecond conversion, 10 channels on 48 pins and 16 channels on 64 and 100 pins |
| DAC | 2 channels of 12 bits with output buffers |
| Programmable voltage detector | eight falling thresholds from 2.00 V to 2.88 V nominal, each with a rising edge about 100 mV higher |
| Debug port | serial wire debug on two pins and JTAG on five, with the trace port sharing low order port bits |
| Backup domain | VBAT domain keeps the RTC, the backup registers and the tamper input alive with the main rail off |
| Flash endurance and retention | 10 kcycles at minus 40 to plus 85 C, 1 kcycle at 105 C, 30 years of retention at 85 C after one kcycle and 10 years at 105 C |
| Thermal resistance junction to ambient | 46 C/W on this package |
| Input tolerance | almost all inputs 5 V tolerant |
| USB | not present, USB full speed is the STM32F102 line |
| Status | production data per the datasheet cover |
Points to check before this part goes on a BOM
Eighty general purpose I/O on a 100 pin body is the reason this code is bought. The value line medium density silicon is the same across the 48, 64 and 100 pin packages, so the converter count stays at 16 and the interface set stays at two SPI, two I2C, three USARTs and one CEC channel; what changes is how many of those signals can be brought out at once without stealing a pin from something else.
The external memory controller is not part of the low and medium density line, and this is where buyers most often expect it. A 100 pin STM32F100VB has no flexible static memory controller, so an address and data bus cannot be hung off it. Where external memory is a requirement the answer is the high density STM32F100VD or VE, which has the controller on the 100 pin body with bank 1 supporting multiplexed NOR or PSRAM.
The 128 Kbytes of Flash with 8 Kbytes of SRAM is the top of this memory range, and the SRAM does not grow with the Flash. On a board with 80 I/O the temptation is to run several ports and a display at once, and each active port plus the display buffer lives in the same 8 Kbytes. A 128 by 64 pixel display buffer with one bit per pixel is 1 Kbyte, and a text buffer with a font table is another, which is exactly the sort of arithmetic that decides between this part and the high density one.
At 46 C/W on the LQFP100 body the package allows about 435 mW from an 85 C ambient to a 105 C junction. Eighty I/O make the thermal question an I/O question: a board that sinks 8 mA on twenty pins is spending 64 mW of the budget on the pins alone, and a display backlight driver or a relay coil taken directly from a port pin can dominate the total. The core at 24 MHz is a modest part of the sum.
The two DAC channels with output buffers are useful on an instrument style board, where they set a reference or a bias without an external converter, and they share pins with two of the 16 converter inputs. The buffered outputs drive a few milliamps, so they suit a high impedance input and not a loudspeaker or a coil. Where more drive is needed the DAC is a reference for an external amplifier rather than the output stage.
The backup domain from VBAT keeps the RTC, the backup registers and the tamper input alive while the main rail is off, which on a 100 pin board is usually wired to a coin cell and to an enclosure switch. The 32 kHz oscillator has a calibration register, and the tamper input is the cheapest way to record that a cover was opened. A board that leaves VBAT and VSSA floating loses both the time and the tamper event on every power cycle.
Flash endurance is 10 kcycles at minus 40 to plus 85 C, and the part is production data in DocID16455 Rev 9. Because the pin count is high, this code often ends up in equipment with a long service life, where a 128 Kbyte image will be field updated several times. Planning two application slots in a 128 Kbyte device leaves 64 Kbytes each, which is workable for a control application and not for one with a large font or a graphics library.
Where this order code fits
It is the 100 pin member of the value line, used where the board needs a lot of digital I/O and a 128 Kbyte image but does not need an external memory bus. Boards comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the Obsolete Part Cross Reference Hub page. Both list the figures that have to match before a substitute goes on a BOM.
Questions buyers ask
Does STM32F100VBT6 have an external memory interface? No. The flexible static memory controller is not present in the STM32F100 low and medium density line. The STM32F100VD and VE parts in the same 100 pin package do have it, with bank 1 able to drive a multiplexed NOR or PSRAM device.
How many converter channels are on the 100 pin body? Sixteen, the same as the 64 pin body and more than the 10 of the 48 pin body. The channel count follows the pin count rather than the memory size, so a 128 Kbyte part in 48 pins still has 10.
Is 8 Kbytes of SRAM enough for a board with a display? For a character display or a small monochrome panel, usually yes, because the buffer is a kilobyte or two. For a colour panel or a full frame buffer it is not, and the choice is the high density part with 24 or 32 Kbytes, or a display with its own controller memory.
SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the Strategic Sourcing page sets out the checks that keep a substitute from failing on the bench.