STM32F100RCT6B
Product Specifications
STM32F100RCT6B
ST — MCU & Embedded Processors
Product Overview
The STM32F100RCT6B from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
- Integrated flash memory and SRAM for efficient code execution
- Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
- Low-power modes for battery-operated and energy-sensitive applications
- Hardware security features: secure boot, crypto accelerator, TRNG
- Extensive development ecosystem with IDE, HAL, and RTOS support
Key Specifications
| Core | — |
| Max Frequency | MHz |
| Flash | KB |
| SRAM | KB |
| GPIO | — |
| ADC | bits |
| Interfaces | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
STM32F100RCT6B: 256 Kbyte, LQFP64 body
STM32F100RCT6B is a member of the STM32F100 value line high density described by DS5944 Rev 11. The order code fixes 256 Kbytes of Flash, 24 Kbytes of SRAM, the LQFP64 body at 10 x 10 mm with 64 pins, 51 general purpose I/O and 16 channels of the 12 bit converter, and the core runs at up to 24 MHz from a 2.0 to 3.6 V supply.
Order code and memory
| Order code | STM32F100RCT6B |
| Program Flash | 256 Kbytes |
| SRAM | 24 Kbytes |
| Package | LQFP64, 10 x 10 mm, 64 pins |
| Maximum general purpose I/O | 51 |
| Analog input channels | 16 of the 12 bit converter |
| Digital to analog converter | 2 channels of 12 bits |
| External memory controller | not present on this body, bank 1 only on the 100 pin body of the same family |
| Supply voltage | 2.0 to 3.6 V |
| Maximum CPU clock | 24 MHz |
| Temperature grade | suffix 6, minus 40 to plus 85 C ambient, 105 C junction |
| Datasheet | DS5944 Rev 11 |
Peripheral and electrical parameters
| Core | ARM Cortex-M3 at up to 24 MHz, 1.25 DMIPS per MHz, single cycle multiply and divide |
| Clock sources | 8 MHz factory trimmed internal RC, PLL up to the 24 MHz core clock, external crystal on the high speed oscillator |
| Timers | one advanced-control 16 bit timer with four channels and complementary outputs, ten general-purpose 16 bit timers and two basic timers, which with the two watchdogs is the sixteen the cover counts |
| Serial interfaces | three SPI blocks, two I2C blocks, three USARTs and two UARTs, plus one HDMI CEC channel |
| DMA | 12 channel DMA across two controllers |
| ADC | 12 bit successive approximation, 16 channels, conversion range 0 to 3.6 V |
| DAC | 2 channels of 12 bits with output buffers |
| Programmable voltage detector | eight falling thresholds from 2.00 V to 2.88 V nominal, each with a rising edge about 100 mV higher |
| Debug port | serial wire debug on two pins and JTAG on five, with the trace port sharing low order port bits |
| Backup domain | VBAT domain keeps the RTC, the backup registers and the tamper input alive with the main rail off |
| Flash endurance and retention | 10 kcycles at minus 40 to plus 85 C, 1 kcycle at 105 C, 30 years of retention at 85 C after one kcycle and 10 years at 105 C |
| Thermal resistance junction to ambient | 49 C/W on this package |
| Input tolerance | almost all inputs 5 V tolerant |
| USB | not present, USB full speed is the STM32F102 line |
| Status | production data per the datasheet cover |
Points to check before this part goes on a BOM
The 64 pin high density code carries 24 Kbytes of SRAM, and that is the figure that decides whether it can replace a medium density part with a firmware change or whether it needs a board change. The 8 Kbytes of the 128 Kbyte medium density code versus 24 Kbytes here is a threefold increase in working memory, but the pin out is the same 51 I/O and the same 16 converter channels, so circuit changes are usually limited to the supply decoupling and the crystal.
Five asynchronous ports on a 64 pin body is unusual, and it is what the three USARTs plus two UARTs provide. In practice a board brings out two or three of them and keeps the rest for internal links such as a radio module and a service header. The pin table decides the combination, because the USART and UART alternate functions are spread across four ports and several of them collide with the SPI and I2C blocks.
Ten general purpose timers plus the advanced-control timer is more timing than most 64 pin boards use, and it is the reason this part appears in multi axis and multi channel equipment. A single advanced timer generates the three complementary pairs for a bridge, four general purpose timers cover the loops and the encoder, and the remainder handle PWM for fans, valves or heaters. The two basic timers trigger the converter and the DAC, so the general purpose set stays free.
The internal letter in the orderable string is the only difference between this code and the unlettered one of the same memory size. Both carry 256 Kbytes of Flash, 24 Kbytes of SRAM, LQFP64 at 10 x 10 mm, 51 general purpose I/O, 16 converter channels, two DAC channels and the high density peripheral set. A bill of materials that names one of them and a warehouse that picks the other is a deviation, not a rounding error.
At 49 C/W the LQFP64 package allows about 410 mW from an 85 C ambient to a 105 C junction. On a 24 Kbyte part with five serial ports and a motor bridge on the same board, the ambient inside the enclosure is the number to use and not the room temperature. The exposed pad soldered into a plane, with vias around it, is what makes the datasheet figure achievable on a dense board.
Flash endurance of 10 kcycles at minus 40 to plus 85 C with 30 years of retention at 85 C after one kcycle is generous for a parameter store and tight for a data log. A 256 Kbyte part has room for two application slots, and a field update that writes the inactive slot is the arrangement that consumes cycles fastest. Counting one update per year against the rating shows the margin; counting one per week does not, and the fallback is to load the image over a serial port into an external memory rather than into the program Flash.
The converter is the same 12 bit block with 16 channels, and the two DAC channels are buffered. On a board that also switches a bridge, the sample timing matters more than the converter accuracy: sampling the phase currents in the middle of a PWM period is what avoids the switching edge, and the advanced timer is what triggers the conversion at that instant. That arrangement is the reason to use a part with an advanced timer rather than to add an external converter.
Where this order code fits
It is the 256 Kbyte high density part in the 10 x 10 mm body with the internal letter, used where a compact board needs 24 Kbytes of SRAM and five asynchronous ports and the memory image is fixed. Boards comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the Component Lead Time Solutions page. Both list the figures that have to match before a substitute goes on a BOM.
Questions buyers ask
What do I gain over the 128 Kbyte medium density code in the same package? Three times the SRAM at 24 Kbytes, twice the Flash, three SPI blocks instead of two, five asynchronous ports instead of three, ten general purpose timers instead of six, and the high density converter with 16 channels. The pin count and the package are the same.
Is the external memory controller available on the 64 pin body? No. It is present on the 100 and 144 pin bodies of this family only. A board that needs a parallel bus has to change package, and that decision is worth taking before the second prototype rather than after.
Does the letter in the order code affect the memory size? No. It is an internal code after the temperature digit. The memory, the package and the peripheral set come from the 256 Kbyte, 64 pin column of Table 2 of DS5944 Rev 11 for both the lettered and the unlettered string.
SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the Obsolete Part Cross Reference Hub page sets out the checks that keep a substitute from failing on the bench.