Contact Us

STM32F100C8T6

Brand: ST
ST STM32F100C8T6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM32F100C8T6 — MCU & Embedded Processors | Superb Automation

STM32F100C8T6

ST — MCU & Embedded Processors

Product Overview

The STM32F100C8T6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM32F100C8T6: 64 Kbyte, LQFP48 body

STM32F100C8T6 is a member of the STM32F100 value line low and medium density described by DocID16455 Rev 9. The order code fixes 64 Kbytes of Flash, 8 Kbytes of SRAM, the LQFP48 body at 7 x 7 mm with 48 pins, 37 general purpose I/O and 10 channels of the 12 bit converter, and the core runs at up to 24 MHz from a 2.0 to 3.6 V supply.

Order code and memory

Order codeSTM32F100C8T6
Program Flash64 Kbytes
SRAM8 Kbytes
PackageLQFP48, 7 x 7 mm, 48 pins
Maximum general purpose I/O37
Analog input channels10 of the 12 bit converter
Digital to analog converter2 channels of 12 bits
External memory controllernot present on this body
Supply voltage2.0 to 3.6 V
Maximum CPU clock24 MHz
Temperature gradesuffix 6, minus 40 to plus 85 C ambient, 105 C junction
DatasheetDocID16455 Rev 9

Peripheral and electrical parameters

CoreARM Cortex-M3 at up to 24 MHz, 1.25 DMIPS per MHz, single cycle multiply and divide
Clock sources8 MHz factory trimmed internal RC, PLL up to the 24 MHz core clock, external crystal range 4 to 24 MHz
Timersone advanced-control 16 bit timer with four channels and complementary outputs with dead time, up to six general-purpose 16 bit timers with four compare channels each, and two basic timers that trigger the converter
Serial interfacesup to two SPI blocks, two I2C blocks and three USARTs, plus one HDMI CEC channel
DMA7 channel DMA controller
ADC12 bit successive approximation, 1 microsecond conversion, 10 channels on 48 pins and 16 channels on 64 and 100 pins
DAC2 channels of 12 bits with output buffers
Programmable voltage detectoreight falling thresholds from 2.00 V to 2.88 V nominal, each with a rising edge about 100 mV higher
Debug portserial wire debug on two pins and JTAG on five, with the trace port sharing low order port bits
Backup domainVBAT domain keeps the RTC, the backup registers and the tamper input alive with the main rail off
Flash endurance and retention10 kcycles at minus 40 to plus 85 C, 1 kcycle at 105 C, 30 years of retention at 85 C after one kcycle and 10 years at 105 C
Thermal resistance junction to ambient55 C/W on this package
Input tolerancealmost all inputs 5 V tolerant
USBnot present, USB full speed is the STM32F102 line
Statusproduction data per the datasheet cover

Points to check before this part goes on a BOM

The 64 Kbyte parts of this line are medium density devices in the reference manual, and the split matters: from this memory size upward the pin out carries the second SPI block, the second I2C block and the third USART, which the 16 and 32 Kbyte codes do not have on 48 pins. Reading the order code before the peripheral list is therefore the right order, because the same 37 I/O body offers a different set of serial interfaces depending on the memory column.

The 8 Kbytes of SRAM doubles the working room without changing the package. Two 512 byte protocol buffers, a 1 Kbyte calibration table, the stack and the heap now fit together, and the 7 channel DMA controller can run the converter and a USART at the same time without the application copying samples by hand. The step from 4 to 8 Kbytes is worth more on this line than the step from 32 to 64 Kbytes of Flash, because Flash is rarely the thing that runs out first.

The 48 pin body still has only 10 converter channels, and that number does not move with memory size. A board that scans a motor current, a bus voltage, a thermistor and a potentiometer uses four of them, which leaves six for a keypad or a second sensor group. Boards that need the full 16 channels have to move to the 64 pin or 100 pin body, where the same silicon brings out the extra analog inputs rather than a larger memory.

At 55 C/W on this package, the 20 C between 85 C ambient and 105 C junction is about 360 mW. On a medium density part the two converters plus the DAC buffers are all inside that budget, and the DAC output buffers alone are a load on the analog supply rather than on the core. A 3.3 V rail that also feeds the reference pin has to be quiet enough for both, which is where a separate ferrite and a 100 nF at each supply pin earns its place.

The internal 8 MHz oscillator is within 1.1 percent at 25 C and 2.2 percent over the temperature range, and the PLL takes it to the 24 MHz core clock. That is good enough for the converter and for short USART links, but three USARTs running at 115200 baud over long cable do not tolerate 2.2 percent of clock error together with the receiver error, so a 4 to 24 MHz crystal is the usual answer once more than one port is in use.

The part is production data in DocID16455 Rev 9, and its 10 kcycle endurance at minus 40 to plus 85 C is the figure that matters if the application writes calibration or a runtime counter to Flash. A log that writes once a second fills a 10 kcycle budget in under three hours, so the endurance number is a reason to keep the counters in the backup registers or in an external memory rather than in Flash.

The CEC channel and the two DAC channels share the analog and digital pin map with the rest of port A and port B, so a board that uses both the DAC outputs and the CEC line has to check the pin table rather than assume the functions can coexist. On a 48 pin body that check is quick, and it is the same check that decides whether the second I2C block is actually available on the connector.

Where this order code fits

It is the 64 Kbyte step in the same 48 pin body, which is the usual choice when the application outgrows 32 Kbytes but the board cannot take a 64 pin package. Boards comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the Component Lead Time Solutions page. Both list the figures that have to match before a substitute goes on a BOM.

Questions buyers ask

What does this part add over the 32 Kbyte version in the same package? Double the SRAM, from 4 to 8 Kbytes, and the medium density peripheral set, which brings the second SPI block, the second I2C block and the third USART onto the 48 pin body. The pin count, the package, the converter channel count and the clock ceiling are unchanged.

Does the 64 Kbyte code have the external memory controller? No. The flexible static memory controller is not part of the STM32F100 low and medium density line at any memory size. External memory on this family means the high density parts in the 100 and 144 pin bodies, where the controller exists and where the pin count can carry an address and data bus.

How much RAM does the DMA controller need? One buffer per stream that is active, plus the descriptor the firmware keeps. With 8 Kbytes there is room for a converter buffer, a USART receive buffer and a transmit buffer at the same time, which is what makes a 7 channel controller useful on this part rather than something the firmware has to schedule around.

SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.