Contact Us

STM32F100C4T6

Brand: ST
ST STM32F100C4T6 is a mcu & embedded component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

STM32F100C4T6 — MCU & Embedded Processors | Superb Automation

STM32F100C4T6

ST — MCU & Embedded Processors

Product Overview

The STM32F100C4T6 from ST is a microcontroller / embedded processor engineered for real-time control, signal processing, and connectivity. STMicroelectronics is a European semiconductor leader with a strong portfolio in MCUs, power management, sensors, and analog ICs.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • ARM Cortex / RISC-V / proprietary core with high-performance real-time processing
  • Integrated flash memory and SRAM for efficient code execution
  • Rich peripheral set: UART, SPI, I2C, ADC, timers, PWM
  • Low-power modes for battery-operated and energy-sensitive applications
  • Hardware security features: secure boot, crypto accelerator, TRNG
  • Extensive development ecosystem with IDE, HAL, and RTOS support

Key Specifications

Core—
Max FrequencyMHz
FlashKB
SRAMKB
GPIO—
ADCbits
Interfaces—
Supply VoltageV
Operating Temp°C
Package—

Applications

Industrial Motor Control IoT Edge Nodes Consumer Electronics Automotive Body Control Smart Home & Appliances Medical Portable Devices

Request Quote — In Stock, 100% New & Original, Full Warranty

STM32F100C4T6: 16 Kbyte, LQFP48 body

STM32F100C4T6 is a member of the STM32F100 value line low and medium density described by DocID16455 Rev 9. The order code fixes 16 Kbytes of Flash, 4 Kbytes of SRAM, the LQFP48 body at 7 x 7 mm with 48 pins, 37 general purpose I/O and 10 channels of the 12 bit converter, and the core runs at up to 24 MHz from a 2.0 to 3.6 V supply.

Order code and memory

Order codeSTM32F100C4T6
Program Flash16 Kbytes
SRAM4 Kbytes
PackageLQFP48, 7 x 7 mm, 48 pins
Maximum general purpose I/O37
Analog input channels10 of the 12 bit converter
Digital to analog converter2 channels of 12 bits
External memory controllernot present on this body
Supply voltage2.0 to 3.6 V
Maximum CPU clock24 MHz
Temperature gradesuffix 6, minus 40 to plus 85 C ambient, 105 C junction
DatasheetDocID16455 Rev 9

Peripheral and electrical parameters

CoreARM Cortex-M3 at up to 24 MHz, 1.25 DMIPS per MHz, single cycle multiply and divide
Clock sources8 MHz factory trimmed internal RC, PLL up to the 24 MHz core clock, external crystal range 4 to 24 MHz
Timersone advanced-control 16 bit timer with four channels and complementary outputs with dead time, up to six general-purpose 16 bit timers with four compare channels each, and two basic timers that trigger the converter
Serial interfacesup to two SPI blocks, two I2C blocks and three USARTs, plus one HDMI CEC channel
DMA7 channel DMA controller
ADC12 bit successive approximation, 1 microsecond conversion, 10 channels on 48 pins and 16 channels on 64 and 100 pins
DAC2 channels of 12 bits with output buffers
Programmable voltage detectoreight falling thresholds from 2.00 V to 2.88 V nominal, each with a rising edge about 100 mV higher
Debug portserial wire debug on two pins and JTAG on five, with the trace port sharing low order port bits
Backup domainVBAT domain keeps the RTC, the backup registers and the tamper input alive with the main rail off
Flash endurance and retention10 kcycles at minus 40 to plus 85 C, 1 kcycle at 105 C, 30 years of retention at 85 C after one kcycle and 10 years at 105 C
Thermal resistance junction to ambient55 C/W on this package
Input tolerancealmost all inputs 5 V tolerant
USBnot present, USB full speed is the STM32F102 line
Statusproduction data per the datasheet cover

Points to check before this part goes on a BOM

16 Kbytes of Flash with 4 Kbytes of SRAM is the smallest pairing in the line, and it changes what the part is good for rather than how fast it runs. The core is the same 24 MHz Cortex-M3 with single cycle multiply and divide, the converter is the same 12 bit block, and the 7 channel DMA controller is present, so the difference is entirely how much code and data fit. A bootloader plus a control loop plus a serial protocol fits; a bootloader plus two protocol stacks plus floating point maths does not.

The low density peripheral set on this code is one SPI block, one I2C block and two of the three USARTs on 48 pins, with the third USART and the second SPI and I2C blocks reserved for the 64 and 128 Kbyte codes. That is worth stating on a drawing, because the package and the pin count are identical across the whole 48 pin range and only the memory column of Table 2 differs. A second source picked by package alone will be short of an interface.

The 10 converter channels on a 48 pin body are shared with the two DAC outputs and with the serial interfaces, so the analog count is the first thing to fix on this part. A motor control board that samples three phase current, a bus voltage and a thermistor uses five, and a board that adds a potentiometer and a keypad uses seven, which still leaves three. Beyond that the 64 pin body with 16 channels is the answer rather than a multiplexer.

The advanced-control timer with complementary outputs and programmable dead time is present even at this memory size, and on a 16 Kbyte part that is the whole point: a three phase bridge driver with dead time inserted by the timer needs no external logic and no interrupt level timing. The remaining general purpose timers handle the control loop, the encoder interface where one is used, and the timebase, and the two basic timers trigger the converter and the DAC.

Because the Flash is small, the endurance question comes up sooner. The line is rated 10 kcycles at minus 40 to plus 85 C, with 30 years of retention at 85 C after one kcycle. A device that writes a runtime hour meter or a valve position to Flash every minute is inside the rating for a few years, but a device that writes every second is not, so the counters belong in the backup registers, which are kept alive from VBAT, or in an external memory.

The LQFP48 package at 55 C/W leaves about 360 mW between 85 C ambient and the 105 C junction limit. A small part like this usually runs cool, but a board that drives relay coils or LEDs from the I/O has to add the sink current to the core and converter figures before calling the thermal question closed. The pin that sinks 8 mA at 0.4 V is dissipating 3.2 mW on its own, and twelve of them is 40 mW of the budget.

The internal RC oscillator is adequate for the converter and for a single short serial link and is not adequate for three ports at high baud over cable. On this memory size the crystal is often left out to save two pins and two components, and the firmware then has to accept the frequency tolerance over temperature. Where the board does fit a crystal, the external oscillator accepts 4 to 24 MHz and the PLL takes the result to the 24 MHz core clock.

Where this order code fits

It is the 16 Kbyte entry point in the family, used where a board needs a 32 bit core, a 12 bit converter and a 7 x 7 mm footprint and the firmware is a few kilobytes of control code. Boards comparing it against a neighbouring memory size or pin count start from our MCU Cross Reference page, and boards replacing a line that has gone end of life start from the One Stop BOM Sourcing page. Both list the figures that have to match before a substitute goes on a BOM.

Questions buyers ask

Is 16 Kbytes of Flash realistic for a production board? For a control loop, a keypad or a sensor interface with one serial protocol, yes. The limit is reached when a field update mechanism needs two application slots, when a stack such as a file system is added, or when floating point maths and a maths library are both linked. The 4 Kbytes of SRAM usually runs out first anyway.

What is the difference between this part and the 32 Kbyte code in the same package? Only the memory. The package, the pin count, the 37 I/O, the 10 converter channels, the two DAC channels, the 7 channel DMA controller and the clock ceiling are identical, and so is the peripheral set on 48 pins. Moving up within the low density codes is a memory decision that needs no board change.

Does this part have a temperature sensor? Yes, an internal sensor connected to a dedicated converter channel, which is how the firmware can compensate a measurement for the die temperature. It measures the die rather than the ambient air, so it is useful for drift correction and not as a room thermometer.

SUPERB holds and sources ST microcontroller lines including this order code for production and repair demand, quoted against the exact ordering string with date codes and packing stated. When a line is changing, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.