Contact Us

VBQG8218

Brand: VBsemi
VBsemi VBQG8218 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBQG8218 — Discrete & Power Semiconductors | Superb Automation

VBQG8218

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBQG8218 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBQG8218: a minus 20 V P channel at 18 milliohm

The VBQG8218 is a single P channel in the thermally enhanced DFN 2 by 2, printed at minus 20 V with 18 milliohm at a minus 4.5 V gate and 22 milliohm at minus 2.5 V, minus 10 A at a 25 C case, minus 9 A on the reduced drive column, 18 nC of gate charge and a gate window of plus or minus 12 V. The data sheet names load switch, PA switch and battery switch for portable devices. The 18 milliohm at 4.5 V is the lowest in this band, and it is bought for exactly that: a battery path where the drop matters more than the voltage margin.

The sheet prints no 10 V resistance column at all, which is unusual and worth reading as a statement. The part is specified where it is used, on a gate driven from a 4.5 V or a 2.5 V rail, and a 10 V drive does not make it meaningfully better than 18 milliohm. A buyer who wants a number for a 12 V gate has to ask for it rather than infer it.

The two currents, minus 10 A at a 25 C case and minus 9 A on the reduced column, sit close together, which says the current is limited by the package rather than by the gate drive. That is consistent with a die that is wide and a body that is only 2 mm square: the pad can pass 10 A for a short time and the board decides the rest.

Key data for the VBQG8218

ConfigurationSingle P channel
PackageThermally enhanced DFN 2 by 2, leadless
VDSMinus 20 V
VGSPlus or minus 12 V
RDS(on) at minus 4.5 V18 milliohm at minus 10 A
RDS(on) at minus 2.5 V22 milliohm at minus 9 A
ID at a 25 C caseMinus 10 A, minus 8 A at a 70 C case
Pulsed drain currentMinus 32 A
Power dissipation3.3 W at a 25 C ambient, 2.1 W at a 70 C ambient
Gate charge18 nC typical
RthJA28 K per watt typical, 38 maximum at 5 s
RthJC5.6 K per watt typical, 7.5 maximum
Junction rangeMinus 55 to 150 C
SolderingPeak 250 C, manual iron rework not recommended

The power dissipation rows are printed against the ambient rather than the case on this sheet, 3.3 W at 25 C and 2.1 W at 70 C, which is the honest way to present a leadless body with no lead frame to speak of. At 3 A and 18 milliohm the loss is 0.16 W, a fifth of the 25 C figure, so the part runs cool even in a warm enclosure. At 8 A the loss is 1.15 W and the margin is gone once the ambient passes 60 C.

The junction to case resistance of 5.6 K per watt is very low for a 2 by 2 body, and it only means something if the pad is soldered without voids. The sheet itself says a solder fillet at the exposed copper tip of a leadless terminal cannot be guaranteed, which is a reminder that this part is judged by the joint underneath and not by what a visual inspection can see.

Where a minus 20 V part at 18 milliohm is used

The first case is a battery switch in a phone or a tablet, where the part sits between the pack and the system rail and passes 2 to 5 A in normal use with peaks to 8 A on a camera flash. At 5 A and 18 milliohm the drop is 90 mV, which is a tenth of the tolerance on a 3.8 V rail, and the 12 V gate window is far from the 4.2 V pack voltage.

The second case is a PA switch in a handheld radio or a portable access point. The power amplifier draws 1 to 2 A in bursts and has to be isolated between transmissions, and the 18 nC of gate charge allows the switch to be cycled at a few kilohertz without a driver. The body diode faces the amplifier, so a reversed supply cannot back feed the pack.

The third case is a charger path switch, where the part selects between a USB input and a wireless receiver output. Both sources are below 12 V, the 18 milliohm gives a 36 mV drop at 2 A, and the gate is pulled to ground through a control transistor referenced to the higher of the two sources.

Gate drive, inrush and the leadless joint

With 18 nC of gate charge and a 12 V gate window, the part can be driven from the pack through a 10 k resistor in a few hundred microseconds, or switched in a few microseconds with a small N channel pulling the gate down through 100 ohm. The inrush into a 100 microfarad load at 4 A is about 20 microcoulombs of gate charge worth of time, which is why a capacitor from gate to source is used to slow the turn on rather than a bigger resistor that also slows the turn off.

The 3.3 W ambient power figure and the 28 K per watt path mean the copper under the pad is the rating. A pad soldered to 25 square millimetres of copper with four vias into a ground plane gives close to 28 K per watt; the same pad on a two layer board with no plane gives 60 or more. On a part this small the vias are worth more than the copper area.

Where the battery path carries two codes across several products, the BOM consolidation page covers how a family is merged onto fewer codes without losing a qualification. Here the argument is simple: this part covers a single cell pack and a charger path, and the minus 30 V member of the family is only needed where a two cell pack or a 12 V rail is present.

What to check before this code is bought

The gate window of plus or minus 12 V is the tightest constraint on this part. On a 12 V rail a gate pulled to ground is exactly at the limit, and on a two cell pack at 8.4 V there is margin. Any circuit that can put 12 V or more across the gate has to clamp it, and the clamp belongs on the board rather than in the test procedure.

There is no 10 V resistance column and no avalanche rating on the sheet. A circuit that relies on a 12 V gate drive, or on the part absorbing the energy of an inductive load, has to ask the vendor rather than assume the numbers scale from the 4.5 V column.

Where the part arrives in volume, the incoming inspection plan page covers what is checked on receipt, from the reel label to a curve trace on a sample. On a leadless body the visual check cannot see the joint, so the inspection is about the lot and the packing rather than the part.

The sheet also says that manual soldering with an iron is not recommended, which matters for a prototype or a rework station. A part replaced by hand on a 2 by 2 pad usually has a void under the pad, and that void turns 28 K per watt into something the part was never rated for. Rework should be done with hot air and a stencil printed paste, or not at all.

Questions we get on this code

Is 18 milliohm measured at 4.5 V or lower? At 4.5 V with a minus 10 A drain current. The sheet prints no 10 V column, so there is no lower figure, and 18 milliohm is the number to use for any gate above 4.5 V.

Can it switch a 12 V rail? It can switch a 12 V rail if the gate is clamped. The part is rated minus 20 V drain to source, so 12 V is inside the rating, but the gate window of plus or minus 12 V is reached at exactly 12 V of drive.

Is 10 A the continuous current? With the case at 25 C. At a 70 C case it is 8 A, and in a 60 C enclosure with 28 K per watt the practical continuous figure is 5 to 6 A.

Why does the sheet warn against iron rework? Because the terminal is exposed copper with no guaranteed fillet, and a hand joint leaves a void under the pad. The thermal path is the joint, so rework by hand risks a part that works and overheats.