VBQG1620
Product Specifications
VBQG1620
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBQG1620 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBQG1620: a 60 V N channel at 19 milliohm in the 2 by 2 DFN
The VBQG1620 is the 60 V member of the same 2 by 2 family, printed at 19 milliohm with a 10 V gate and 21 milliohm with 4.5 V, 14 A at a 25 C case and 11 A at a 70 C case, with a 1.5 V threshold and 1800 pF of input capacitance. The data sheet names notebook CPU core and high side synchronous rectifier as the applications. The resistance is a quarter of the hundred volt part in the same body, which is what a shorter drift region buys, and that is the whole reason two voltage classes exist in one footprint.
The threshold of 1.5 V is the lowest in this small body band. It makes the part easy to drive from a 4.5 V rail and it also means the part is partly on at 3.3 V and can be turned on by a leak through a pull up resistor. On a hot side gate drive that is not a problem, because the driver holds the gate down. On a battery fed circuit where the gate floats while the supply is off, it is a path for current that nobody planned.
The 19 milliohm figure is printed at 10 A and the 21 milliohm at 9 A, so the two conditions differ in current as well as gate voltage. That is normal on these sheets, and it makes the 4.5 V number slightly optimistic in a comparison, because the lower current also lowers the junction temperature rise and the resistance with it.
Key data for the VBQG1620
| Configuration | Single N channel |
| Package | DFN 2 by 2 with exposed pad |
| VDS | 60 V |
| VGS | Plus or minus 20 V |
| Vth | 1.5 V typical at 250 microamp |
| RDS(on) at 10 V | 19 milliohm at 10 A |
| RDS(on) at 4.5 V | 21 milliohm at 9 A |
| ID at a 25 C case | 14 A, 11 A at a 70 C case |
| ID at a 25 C ambient | Published on the ambient rows, well below the 14 A case figure |
| Pulsed drain current | 42 A |
| Ciss | 1800 pF at 15 V |
| Gate charge | 15 nC typical, 23 nC maximum in the table, 7.2 nC in the summary line |
| Body diode | 0.8 V at 9 A, 15 ns recovery typical |
| RthJA | 39 K per watt typical, 55 maximum at 10 s |
| Junction range | Minus 55 to 150 C |
The same gate charge discrepancy appears here as on the hundred volt part in this family, 7.2 nC in the summary against 15 nC typical and 23 nC maximum in the table. Because both sheets were built from the same template, it is likely one line was not updated when the die changed, and the table is the more likely survivor. Either way, the drive current for a 500 kHz converter has to be sized on the maximum, because a driver rated at 15 nC and asked to move 23 nC at the same frequency will run out of gate current and slow the edge.
The 1800 pF input capacitance is high for a 2 by 2 body at this resistance, and it is the price of the larger die that gives the 19 milliohm. At 500 kHz the drive loss in the gate is the charge times the voltage times the frequency, so 15 nC at 5 V is 37 mW, which is nothing. The capacitance matters for the driver output impedance and for the ringing on the gate loop, not for the steady state loss.
Where a 60 V part at this resistance is used
The first case is the high side switch of a buck converter running from a 20 to 28 V adapter into a 1 to 3.3 V core rail at 10 to 15 A. The switch carries the full inductor current for part of the cycle, and at 12 A and 21 milliohm the conduction loss is 3 W times the duty cycle, so about 0.5 W at a 20 per cent duty. The 60 V rating covers the adapter plus the ringing, and a 40 V part would be marginal on a 28 V input once the overshoot is counted.
The second case is a synchronous rectifier in the same converter. Here the part conducts for the rest of the cycle and the body diode carries the current during the dead time. The 0.8 V drop at 9 A and the 15 ns recovery define the dead time loss, and a part with a slower diode would need a longer blanking window and lose more efficiency at light load.
The third case is a load switch on a 48 V battery line for a portable instrument. The 60 V rating covers the 54.6 V of a full pack plus a small margin, and the 14 A case current is far above the 2 to 4 A the instrument draws, so the part runs cold and the 39 K per watt junction to ambient is what keeps it there.
Drive, gate loop and thermal path
At 1.5 V threshold the part is fully enhanced by 4.5 V and hard on by 10 V, so a 5 V driver sits comfortably above the knee. The gate loop should be short, because 1800 pF with 5 nH of trace inductance rings at about 53 MHz, and that ring is what a gate resistor of 2 to 5 ohm is there to damp. A resistor larger than 10 ohm slows the edge enough that the crossover loss in the switch becomes larger than the ringing it removes.
The thermal path runs from the die through the exposed pad into the board copper. The junction to foot resistance is 25 K per watt typical and 29 maximum, so the pad soldering is the limiting feature, not the plastic. A pad with 60 per cent voiding turns 25 K per watt into something closer to 60, which is the failure mode seen most often on this body in the field, and it shows up as a part that works on the bench and fails in a warm enclosure.
Where a 60 V part is being compared with the 40 V and 100 V members of the same footprint, the power management cross reference page sets out which parameters have to match before a substitute is proposed, from threshold and gate charge to the avalanche rating. In this family the footprint is identical across the three voltage classes, so the decision is made on margin and resistance, and the 60 V part is usually the one that keeps a 28 V adapter with ringing inside its rating without paying the hundred volt price in milliohms.
What to check before this code is bought
The part is an industrial grade device. There is no automotive qualification, no statement of the moisture sensitivity level and no mission profile in the sheet. For a build that has to survive a thermal cycle test in an enclosure, the figure to watch is not the 14 A but the 39 K per watt, because the ambient inside an enclosure is 55 to 65 C and the part is then allowed about 1.5 W.
The threshold being 1.5 V is worth a specific check on any circuit where the gate can float. A pull down of 10 k on the gate keeps the part off when the driver is unpowered, and without it a leak from the drain through the gate oxide or from a neighbouring rail can turn the part partly on. This is a circuit question rather than a part question, but it is the one that bites with a low threshold part.
Where the code arrives in volume, the incoming inspection plan page covers what is checked on receipt, from the reel label and the lot code to a curve trace on a sample, before the parts reach the line. On a 2 by 2 body the marking is small and the label is the record, so a mixed reel is the risk to catch at the door.
The part also needs a look at the reel quantity and the packing before a production order. A 2 by 2 DFN usually comes on an 8 mm tape, and the pocket depth matters when the pick and place nozzle is set for a body with a 0.8 mm height. A tape that is too shallow leaves the part tilted and the placement offset shows up as a solder void under the pad.
Questions we get on this code
Is 14 A the current the part can carry on a board? Only with the case held at 25 C. The 70 C case row is 11 A, and the ambient rows are lower still. On a normal board with a warm enclosure, 6 to 8 A continuous is the honest figure at 21 milliohm.
Does the 1.5 V threshold cause false turn on? It can, on a circuit where the gate floats. The threshold is the point where 250 microamp flows, and a part at that point is not off in any useful sense. A 10 k pull down on the gate removes the risk.
Can this part replace the hundred volt member of the family? Only if the rail is below about 40 V including the overshoot. The footprint and the pin out are the same, so the swap fits, but the voltage margin is gone and a 60 V part on a 48 V rail with 12 V of ringing is at its limit.
Why does the summary print a different gate charge from the table? The sheet contradicts itself between 7.2 nC and 15 nC typical. We quote both rather than pick one, and we size the driver for the 23 nC maximum until the vendor confirms.