Contact Us

VBQF1307

Brand: VBsemi
VBsemi VBQF1307 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBQF1307 — Discrete & Power Semiconductors | Superb Automation

VBQF1307

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBQF1307 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBQF1307: a 30 V N channel at 7.5 milliohm in a 3 by 3

The VBQF1307 is a single N channel MOSFET in the DFN8 3 by 3 body at 30 V, plus or minus 20 V on the gate, a 1.7 V threshold, 35 A of drain current, 9 milliohm at a 4.5 V gate and 7.5 milliohm at a 10 V gate. It is the smallest die of the 30 V family in this body, and the one that shows how far the gate charge can be brought down.

At 7.5 milliohm and 10 A the loss is 0.75 W, at 20 A it is 3 W, so this part is comfortable at 8 to 12 A and marginal above 15 A on a 3 by 3 pad. Its advantage over the lower resistance members is a gate charge roughly half theirs, which makes it a candidate for the high side of a converter where switching loss dominates.

The 35 A rating is a die figure at a 25 C case. The part is chosen for its switching behaviour and its cost, and the current rating is the least interesting number on the page for this one.

Key data for the VBQF1307

ConfigurationSingle N channel
PackageDFN8 3 by 3, exposed pad
VDS30 V
VGSPlus or minus 20 V
Vth1.7 V typical
ID35 A at a 25 C case
RDS(on) at 4.5 V9 milliohm
RDS(on) at 10 V7.5 milliohm
StructureTrench
Conduction at 5 A0.19 W
Conduction at 10 A0.75 W
Conduction at 15 A1.7 W
Conduction at 20 A3 W

The gate charge is the reason this member exists. At the same 30 V rating the 2 milliohm part carries roughly twice the gate charge, so at 500 kHz the drive loss and the switching loss are both higher. For the high side of a buck that switches the full rail, a 7.5 milliohm part with half the charge can show a lower total loss than a 2 milliohm part with twice the charge, and the crossover moves with frequency: at 100 kHz the conduction term dominates and the low resistance part wins, at 500 kHz the charge term does.

Where the higher resistance member is the right one

The first case is the high side of a 12 V to 5 V buck at 200 to 500 kHz. The high side conducts for the duty fraction of the period, 40 per cent here, so its conduction loss at 10 A is 0.3 W against 0.8 W on the low side, while its switching loss is set by its gate charge. The smaller die with half the gate charge wins on the total even though its resistance is higher.

The second case is a load switch that is on most of the time and carries 5 to 8 A. At 7.5 milliohm and 5 A the loss is 0.19 W, which does not need a heatsink and does not need the larger die.

The third case is a portable device power path, where the rail is 3 to 4.2 V and the current is 2 to 4 A. At 4 A the loss is 0.12 W, and the small gate charge keeps the driver small enough to fit in the same package as the charger.

Switching behaviour at 30 V

A 30 V trench part switches a 12 V rail with a 20 to 40 V spike at the switch node, depending on the loop inductance. The 30 V rating leaves little room, so the board arrangement of the input capacitor, the switch and the return path decides whether the part survives. The loop has to be short, the capacitor has to be close, and the gate resistor has to slow the turn on enough that the spike stays under 30 V.

With 7.5 milliohm the part is not the limiting factor in that loop; the parasitic inductance is. A 10 nH loop at 10 A per 10 ns produces 10 V of spike, which is a third of the rating, so the faster the part switches the worse the margin. That is the second reason the higher resistance member is chosen on the high side.

Thermal behaviour and the pad

At 10 A the loss is 0.75 W and at 15 A it is 1.7 W. Hot, the resistance rises by about 40 per cent, so 15 A becomes 2.4 W and a 3 by 3 pad at 35 to 45 K per watt gives an 84 to 108 K rise. That is comfortable at a 60 C ambient and marginal at 85 C.

Reaching 20 A continuously needs more copper under the pad than a 3 by 3 normally gets, and the honest answer for that current is the 4 milliohm part in the same body rather than more copper under this one. The family is arranged so that the current level chooses the member and the copper stays the same.

When the question is which member of the family to hold in stock, the component lead time solutions page covers how the stock position is set against the build plan rather than against the data page.

On a 12 V rail the loop inductance between the input capacitor and the switch is what sets the spike, and at 7.5 milliohm the part is not the limiting element in that loop. Ten nanohenries with 10 A switched in 10 ns gives 10 V of overshoot on top of the 12 V rail, which is close to the rating. Shortening the loop, placing the capacitor within a few millimetres of the drain and using a wide return path under the switch node do more for reliability than any change of part in this family.

Read across the family, 2, 4 and 7.5 milliohm at the same 30 V rating and the same 3 by 3 body are three points on one trade: die area against gate charge and price. The selection follows the current and the frequency rather than the headline. Below 10 A and above 300 kHz the 7.5 milliohm part has the lowest total loss; between 10 and 25 A at 100 to 300 kHz the 4 milliohm part is the balance; above 25 A or below 100 kHz the 2 milliohm part is the only one that keeps the pad inside its temperature limit.

With a 1.7 V threshold this part turns on at a gate voltage a 3.3 V logic pin can reach, which makes it look like a logic level device. It is not: the published resistance is at 4.5 V and 10 V, and at 3.3 V the channel is only 1.6 V above threshold, so the resistance is several times the table value. A 3.3 V system either adds a level shift or accepts the loss, and the loss has to be measured rather than taken from the 4.5 V column.

The sourcing side of this part is covered on the safety stock planning. For a family member held against a build plan, that page covers how much is carried and on what signal it is replenished.

Questions we get on this code

Why not use the 2 milliohm part everywhere? Gate charge and cost. At 5 to 10 A the conduction difference is a few tenths of a watt and the switching and drive difference is larger.

Is 30 V enough on a 12 V rail? With a short loop and a clamped switch node, yes. Without that, the spike at turn off can exceed the rating, which is why the gate resistor matters.

Does the 1.7 V threshold mean it works at 3.3 V? It turns on, but the resistance at 3.3 V is not published. At 4.5 V the figure is 9 milliohm, and 3.3 V will be worse.

Can it be used as a reverse polarity protection part? Yes in the low side, and the body diode blocks when the input is reversed. In the high side the drive has to be referenced to the source.