Contact Us

VBQA3316

Brand: VBsemi
VBsemi VBQA3316 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBQA3316 — Discrete & Power Semiconductors | Superb Automation

VBQA3316

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBQA3316 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBQA3316: two 30 V N channels in one 5 by 6 body

The VBQA3316 is a dual N channel MOSFET in the DFN8 5 by 6 B body, printed at 30 V drain to source, plus or minus 20 V on the gate, a 1.7 V threshold, 22 A per channel of drain current, 24 milliohm at a 4.5 V gate and 18 milliohm at a 10 V gate. Two electrically separate N channels share one package and one thermal pad, which is the reason the part exists.

The value of a dual body is board area and thermal path. Two single 3 by 3 parts take twice the footprint and twice the pad copper; one 5 by 6 with two channels takes one land pattern and one continuous pour under the pad. In a dense DC to DC stage or a two channel load switch that is worth more than the few cents the dual body costs.

The 22 A figure is per channel and it comes with a condition that matters: with both channels conducting at once the package has to dissipate twice the loss through one pad, so the pair together is rated below twice the single channel figure. That is a thermal limit, not a silicon limit.

Key data for the VBQA3316

ConfigurationDual N channel, two separate channels
PackageDFN8 5 by 6 B, exposed pad
VDS30 V per channel
VGSPlus or minus 20 V
Vth1.7 V typical
ID22 A per channel at a 25 C case
RDS(on) at 4.5 V24 milliohm per channel
RDS(on) at 10 V18 milliohm per channel
StructureTrench
Conduction at 3 A0.16 W per channel
Conduction at 5 A0.45 W per channel
Conduction at 8 A1.15 W per channel
Both channels at 8 A2.3 W in one package

Two channels on one die pair are close in threshold, but the vendor table gives one set of numbers and no matching specification. Paralleling them therefore follows the same rules as paralleling two separate parts: a gate resistor on each, a symmetrical drain and source connection, and a board arrangement that keeps the two paths the same length. The gain is real but the package thermal limit does not double, so the pair is worth less than twice one channel at the current where the pad is the limit.

Where a dual 30 V N channel is used

The first case is a synchronous buck low side in a two phase converter, where the two channels switch 180 degrees apart and share one thermal pad. That keeps the two hot dies together, which is better than two parts four centimetres apart on different pours.

The second case is a two channel load switch, one channel per rail, with a single control pin per channel and a shared ground. At 18 milliohm and 3 A the loss is 0.16 W per channel, which is comfortable in still air and leaves the pad free for the copper losses of the rest of the board.

The third case is a dual LED string driver or a dual solenoid driver, where two inductive loads have to be switched independently and each needs its own freewheel diode. The body diode of each channel does that job, so the external diodes can go.

Pinout questions on a dual body

A dual MOSFET in a DFN 5 by 6 is either two isolated channels, a common drain pair or a common source pair, and the vendor drawing decides which. This one is printed as two separate channels, so the drain of each channel is a separate pin and the sources are separate as well, and the pad is normally tied to one of the drains or left floating depending on the family. That has to be read from the package drawing before the land pattern is made, because a pad tied to the wrong node turns the part into a short.

The gate of each channel has its own pin, which matters for a synchronous converter: the two gates need separate resistors so the turn on and turn off rates can be set independently, and a shared gate pin would force the same drive on both.

Losses in one package

Each channel makes 0.16 W at 3 A, 0.45 W at 5 A and 1.15 W at 8 A from 18 milliohm. With both channels loaded the package sees 2.3 W at 8 A each, and the 5 by 6 pad on four square centimetres of copper is 25 to 30 K per watt, so the pair runs at a 60 to 70 K rise. That is a workable continuous point with the ambient at 60 C.

Above that the pad becomes the limit rather than the die. Two channels at 15 A each would be 8.1 W, a 200 to 240 K rise, which is why the 22 A per channel figure is a package and bond wire number rather than a board number. Splitting the two channels onto separate parts does not change the total loss, but it does double the copper under them, and that is sometimes the cheaper way to reach 15 A per channel.

When a dual body is being introduced into an existing BOM, the BOM consolidation page covers how two single parts are merged into one line without losing the qualification that was already signed off on the singles.

Thermal coupling is the hidden cost of a dual body. When one channel carries current and the other is idle, the idle one sits at the temperature of the shared pad, and its leakage and threshold move with that temperature. In a two phase converter this is harmless. In a circuit where one channel is a precision switch and the other is a heater, the coupling has to be part of the budget, and two separate parts on separate pours are the better answer even though they take more board area.

A dual 30 V part fits in a 5 by 6 body because two dies plus their edge termination will not go into a 3 by 3 without halving the area of each. The two dies sit side by side on one lead frame, and the pad under them is common copper, which is why the package runs cooler than two separate 3 by 3 parts. The isolation between the channels is thermal rather than electrical: a gap of a few tens of microns and the mould compound separate them, which is ample at 30 V and would not be at 200 V. That is the reason dual bodies stop at about 60 V and dual parts above that are rare.

The source connection of each channel is what decides the gate loop. In a dual body the two sources leave on separate pins, so each gate loop closes through its own source pin, and a shared source trace between the pin and the star point puts the current of one channel into the gate loop of the other. Two short traces from the pins to the star point, with the driver returning there as well, keep the two loops apart. That is the whole reason the package has separate source pins rather than one.

The sourcing side of this part is covered on the supplier quality audit. For a dual body that has to be second sourced, that page covers what is checked at the source before the lot is released.

Questions we get on this code

Are the two channels matched? They come from one die pair and are close, but the vendor table gives one set of numbers, so matching is not guaranteed to a figure and should not be relied on for current sharing.

Can the two channels be paralleled for 44 A? They can be paralleled at the board level like two separate parts, with a gate resistor on each. The package thermal limit does not double, so the gain is less than the arithmetic suggests.

Is the pad common to both drains? That is decided by the package drawing, not by the electrical table. Confirm it before the land pattern is released.

Does the 1.7 V threshold work with a 3.3 V gate drive? It turns on, but at 24 milliohm rather than 18, so size the loss and the pad for the 4.5 V column.