Contact Us

VBP18R25S

Brand: VBsemi
VBsemi VBP18R25S is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBP18R25S — Discrete & Power Semiconductors | Superb Automation

VBP18R25S

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBP18R25S from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBP18R25S: 800 V and 25 A in a TO247 with 138 milliohm

The VBP18R25S is a single N channel MOSFET in a TO247 body, rated at 800 V drain to source, plus or minus 30 V on the gate, a 3.5 V threshold, 25 A of drain current and 138 milliohm at a 10 V gate. The vendor table lists a superjunction multiple epitaxy die with a standard body diode.

One hundred and thirty eight milliohm at 800 V is the step above the 205 milliohm member of the family, and it buys a third less conduction loss at the same current. At 25 A the die makes 86 W, at 19 A 50 W, at 12 A 20 W and at 6 A 5 W. On a fan cooled heatsink the working current is 12 to 15 A, and on a plate heatsink 7 to 9 A.

The part is the usual choice for a 400 V line drive at 1.5 to 2.2 kW, where the bus is 565 V and the 800 V class has 235 V of margin. Buying the wider margin costs a little resistance against a 600 V part and removes the surge question entirely.

Key data for the VBP18R25S

ConfigurationSingle N channel
PackageTO247, through hole, tab on the drain
VDS800 V
VGSPlus or minus 30 V
Vth3.5 V typical
ID25 A
RDS(on) at 10 V138 milliohm
StructureSuperjunction, multiple epitaxy
Loss at 6 A5.0 W
Loss at 12 A19.9 W
Loss at 19 A49.8 W
Loss at 25 A86.3 W

Margin against the 900 V class

On a 480 V line the bus is 680 V. The 800 V part has 120 V of margin and the 900 V part has 220 V. The resistance penalty for the extra 100 V is around 40 percent at the same die area, so a 900 V part at 138 milliohm is a larger die and a higher price.

Where the load does not regenerate, the 800 V part is enough and the margin of 18 percent covers the clamp. Where the load brakes into the bus, the 900 V part is the only safe choice and the extra cost is part of the drive rather than a part decision.

On a 400 V line the bus is 565 V and the 800 V part has 235 V of margin, which is 42 percent. There the 800 V class is chosen for margin rather than necessity, and a 600 V part would work at 35 V less margin on a surge.

Loss at the working point

At 9 A and 138 milliohm the loss is 11 W cold and 20 W hot. A TO247 on a 1.5 K per watt plate heatsink at 40 C ambient sits at 84 C junction, which is comfortable. At 12 A the hot loss is 36 W and the junction is at 120 C, still inside.

At 15 A the hot loss is 56 W and the junction is at 165 C, which is outside. The ceiling on a plate is 11 to 12 A, and a fan cooled heatsink at 0.6 K per watt moves it to 15 A.

Switching at 565 V and 9 A with a 30 ns crossover is 5 W peak, and averaged at 8 kHz in a drive it is under 1 W. The drive case is dominated by conduction and the resistance sets the choice. A 40 kHz stage is a different calculation where the capacitance loss starts to matter.

Where this part fits

400 V and 480 V three phase drives at 1.5 to 2.2 kW, solar inverters at 600 V string voltage, uninterrupted power stages, and high voltage battery chargers. In a drive the part runs at 4 to 16 kHz and the body diode carries the motor current during the dead time, so the diode drop at 9 A is part of the loss budget.

In a solar inverter the part runs at 16 to 32 kHz with a 600 V string, and the switching loss is a third of the total. There, a part with lower output capacitance at the same resistance is the better buy.

For a 690 V line the class is 1200 V. Where a drive family spans 400 V and 480 V, this part covers both and the supplier onboarding checklist page covers what is verified before a second line is released on the same code.

At 138 milliohm the part is small enough that the copper around it is a comparable resistance. A 3 mm trace on 70 micrometre copper is 1.3 milliohm per 10 mm, and a source return of 30 mm adds 4 milliohm to a 138 milliohm device. That is 3 percent of the total and inside the measurement error, but on a 24 milliohm part the same trace is 15 percent and the board becomes part of the bill of materials. Below 50 milliohm the copper has to be counted, and above 100 milliohm it can be ignored.

The sourcing side of this part is covered on the vendor consolidation. For an 800 V code that several products share, that page covers which lines stay dual sourced after a consolidation.

Questions we get on this code

Is it the same die as the FD part at 140 milliohm? The two print almost the same resistance at the same voltage and current, and differ in the diode grade. They are close enough to be graded from one die, and close enough that a swap is a diode recovery question rather than a conduction question.

Why does the FD part print 140 and this one 138? The difference is inside the grading window and is not a meaningful electrical difference. The grade suffix is the real distinction.

What is the gate charge? Not printed by the vendor. For a 16 kHz drive it does not matter, since the gate loss is a fraction of a watt.

Does it need a negative gate bias? No. The 3.5 V threshold holds it off at 0 V, provided the source connection has low inductance and the driver holds the gate down through a 10 k resistor.