Contact Us

VBP185R50SFD

Brand: VBsemi
VBsemi VBP185R50SFD is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBP185R50SFD — Discrete & Power Semiconductors | Superb Automation

VBP185R50SFD

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBP185R50SFD from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBP185R50SFD: 850 V and 50 A in a TO247 with 90 milliohm

The VBP185R50SFD is a single N channel MOSFET in a TO247 body, rated at 850 V drain to source, plus or minus 30 V on the gate, a 3.5 V threshold, 50 A of drain current and 90 milliohm at a 10 V gate. The vendor table lists a superjunction multiple epitaxy die with an FD fast recovery body diode grade.

Eight hundred and fifty volts is an unusual class. It sits between the 800 V parts used on 480 V three phase lines and the 900 V and 950 V parts used where the surge margin has to be wider. Its purpose is to hold a 480 V AC three phase bus, which rectifies to 680 V, with enough margin for a 20 percent regeneration and a clamped surge.

At 90 milliohm and 50 A the die makes 225 W, at 38 A 130 W, at 25 A 56 W and at 12 A 13 W. On a fan cooled heatsink the working current is 15 to 20 A, and on a plate heatsink 8 to 10 A. The current label is generous against the thermal path, as it is on every part in this voltage class.

Key data for the VBP185R50SFD

ConfigurationSingle N channel
PackageTO247, through hole, tab on the drain
VDS850 V
VGSPlus or minus 30 V
Vth3.5 V typical
ID50 A
RDS(on) at 10 V90 milliohm
StructureSuperjunction, multiple epitaxy
Diode gradeFD, fast recovery body diode
Loss at 12 A13.0 W
Loss at 25 A56.2 W
Loss at 50 A225.0 W

Why 850 V rather than 800 V or 900 V

A 480 V three phase line rectifies to 680 V. An 800 V part has 120 V of margin, which is 18 percent. A regenerating motor load takes the bus to 750 V and a clamped surge to 800 V, which leaves nothing. That is why 800 V parts on a 480 V line are a known weak point in drives that brake hard.

An 850 V part has 170 V of margin, which is 25 percent, and that covers regeneration plus a modest clamp overshoot. A 900 V part has 220 V and costs more per milliohm, so the 850 V class is the cost optimum for a 480 V line with a braking load.

At 600 V input from a solar string the margin is larger and the class is chosen for the string voltage rather than the line. A 15 panel string at 40 V per panel reaches 600 V cold, and 850 V leaves 250 V for the surge.

Loss at the working point

At 15 A and 90 milliohm the loss is 20 W cold and 36 W hot. A TO247 on a 0.7 K per watt heatsink at 45 C ambient sits at 115 C junction, which is inside the limit. At 20 A the hot loss is 65 W and the junction is at 140 C, which is marginal.

Switching adds 3 to 6 W at 40 kHz in a hard switched stage at 680 V, because the higher bus means a larger displacement current through the output capacitance. At 100 kHz the capacitance loss alone is 20 W and the part is no longer a 15 A device.

The FD diode grade matters in a bridge at this voltage, because the recovered charge of a standard body diode at 680 V and 15 A is a significant spike on the opposite switch. In a two switch forward or a single ended stage the body diode never conducts and the grade is not needed.

Where this part fits

Motor drives on a 480 V three phase line at 2 to 4 kW, solar string inverters at 600 V, uninterruptible power stages, and battery chargers for high voltage packs. In a drive the part runs at 8 to 16 kHz and the switching loss is small against the conduction term, so the resistance sets the choice.

In a solar inverter the part runs at 16 to 32 kHz with a 600 V string, and the capacitance loss is a noticeable share. There, a part with a lower output capacitance at the same resistance wins on total loss even if the resistance is slightly higher.

For a 690 V three phase line the class is 1200 V, and this part is not usable. Where a drive family spans 480 V and 690 V, the component obsolescence management page covers how the two voltage classes are watched when one narrows.

The gate drive for an 850 V part is the same as for a 600 V part, but the Miller clamp matters more. At 680 V the displacement current through the drain gate capacitance at a 20 V per ns dv/dt is 0.4 A, and a driver that turns off through a 10 k resistor lets the gate rise until the part turns back on. A dedicated clamp pin, or a 10 ohm turn off path in parallel with the 10 k, is what keeps the part off during the opposite switch transition. Without it the bridge shows a shoot through current that looks like a snubber failure.

The sourcing side of this part is covered on the safety stock planning. For a thin voltage class, that page covers how much is held when only a few lines make the part.

Questions we get on this code

Is 850 V a standard class? It is a real class but a thin one, made by fewer lines than 800 V or 900 V. That thinness is the sourcing risk, and it is worth a second source before the first build.

Can an 800 V part be used instead? On a 480 V line with a braking load, no. The bus reaches 750 V and the margin disappears. On a 400 V line, an 800 V part is already more than enough.

What is the hot resistance? Roughly 1.8 times the printed value at 125 C. Size at 160 milliohm hot for a thermal calculation.

Is the FD grade needed in a boost stage? No. The body diode does not conduct in a boost, so the standard grade is equivalent and usually cheaper.