Contact Us

VBP165R43SE

Brand: VBsemi
VBsemi VBP165R43SE is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBP165R43SE — Discrete & Power Semiconductors | Superb Automation

VBP165R43SE

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBP165R43SE from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBP165R43SE: 650 V and 43 A in a TO247 with 58 milliohm

The VBP165R43SE is a single N channel MOSFET in a TO247 body, rated at 650 V drain to source, plus or minus 30 V on the gate, a 3.5 V threshold, 43 A of drain current and 58 milliohm at a 10 V gate. The vendor table lists the die as superjunction deep trench. The SE suffix marks the deep trench column structure rather than the multiple epitaxy structure used by the other superjunction parts in this band.

The difference between multiple epitaxy and deep trench is how the p columns are built. Multiple epitaxy grows and implants the columns layer by layer, which is slower per wafer and gives a smoother charge balance. Deep trench etches the columns and fills them in one pass, which is cheaper per wafer and gives a sharper vertical profile. Both reach the same class of on resistance, and the choice between them is a supplier question rather than a circuit question.

Fifty eight milliohm at 43 A puts this part between the 36 A and the 70 A members of the family. At 43 A the die makes 107 W, at 32 A 59 W, at 22 A 28 W and at 11 A 7 W. On a fan cooled heatsink the working current is 20 to 25 A, and on a plate heatsink 12 to 15 A.

Key data for the VBP165R43SE

ConfigurationSingle N channel
PackageTO247, through hole, tab on the drain
VDS650 V
VGSPlus or minus 30 V
Vth3.5 V typical
ID43 A
RDS(on) at 10 V58 milliohm
StructureSuperjunction, deep trench
Loss at 11 A7.0 W
Loss at 22 A28.1 W
Loss at 32 A59.4 W
Loss at 43 A107.2 W

Why the middle of a family is the hardest to source

Families are bought at the ends. The smallest member is the cheap auxiliary switch and the largest is the main switch of the biggest stage, so distributors hold stock at both ends and the middle member sits on allocation for most of the year. A 43 A part in a family that runs from 20 A to 90 A is exactly the one that gets substituted without notice.

The substitute is usually a nearby member with the same footprint and a different current label. A 47 A part at 75 milliohm drops into the same holes, and the board works on the bench because the load is light. At full load it runs 10 C hotter and the field returns start at month four. That pattern is the reason a middle-of-family code needs a documented second source rather than a distributor promise.

On the purchase side the question to ask is not whether the part is available but which grade of the same die is available on the same date. The supplier scorecard page covers how delivery and substitution behaviour are scored over a year rather than a quarter.

Loss and thermal at the working point.

At 20 A continuous and 58 milliohm the conduction loss is 23 W. A TO247 on a 1 K per watt heatsink with a 40 C ambient puts the junction at 103 C, which is inside the usual 150 C ceiling with margin for a hot day. At 25 A the loss is 36 W and the junction is at 116 C, still inside but with less room.

The temperature coefficient decides how much of that margin is real. A superjunction die at this voltage typically rises 80 to 100 percent from 25 C to 125 C, so 58 milliohm cold is 105 to 115 milliohm hot, and the 25 A loss is then 65 to 72 W rather than 36 W. The calculation has to be done hot, and the hot number is the one that sizes the heatsink.

Switching loss adds 1 to 3 W at 60 to 100 kHz in a hard switched stage. In a soft switched LLC it is under 1 W, and the conduction term is the whole budget. The frequency is therefore the variable that decides whether this part or the 70 A member is the cheaper total.

The 650 V rating in a 400 V system

A single phase 230 V line gives a 325 V bus, and a boost stage holds 400 V. The steady state margin to 650 V is 250 V, and a surge clamped at 550 V leaves 100 V. A two switch forward or a half bridge adds the leakage spike on top, so the clamp is part of the circuit and not a shopping option.

A 480 V three phase line rectifies to 680 V, which is already above the rating, so this part is not usable there at all. A 400 V three phase line rectifies to 565 V and leaves 85 V, which is not enough for a motor load that regenerates. The class belongs on single phase and on 400 V DC links from a battery or a solar string.

Solar is the interesting case. A string of 10 to 12 panels at 40 V open circuit reaches 480 V cold, and a 650 V part has 170 V of margin. A string of 15 panels reaches 600 V and the class is 900 V. String length is therefore a purchasing decision as much as an electrical one.

Where this part fits

Power factor stages from 800 W to 2.5 kW, LLC primaries at 400 V, solar microinverters and string optimisers, and battery chargers with a 400 V link. It also appears in the primary of a two switch forward at 1 to 2 kW, where the two switches share the off state voltage and the clamp diodes recover the leakage energy.

In a hard switched bridge, the body diode recovery of this grade is the parameter to check before release. In a soft switched LLC the recovery does not appear and the part is a straight conduction device.

For a board that has to run at 50 C ambient inside a sealed enclosure, the part is a 12 to 15 A device rather than a 25 A one, and the enclosure is the limit rather than the die.

The sourcing side of this part is covered on the strategic sourcing. For a middle of family code, that page covers how the source is held when the ends of the family are on allocation.

Questions we get on this code

Is deep trench better than multiple epitaxy? For the circuit, no difference at the terminals. For the supplier, deep trench is cheaper per wafer, which shows up in the price and in the delivery. For reliability, both are qualified to the same class by the same makers.

What is the hot resistance? The table gives the cold figure only. Ask for the curve, and if there is none, size at 1.9 times the printed value for a 125 C junction.

Can it run at 43 A continuously? No. At 43 A the die makes 107 W cold and 190 W hot, which no TO247 can pass to a heatsink. The printed current is a die rating at a 25 C case, not a working point.

What is the difference from the 47 A part at 75 milliohm? The 47 A part has the higher resistance and the higher current label, so the two overlap. Compare them on total loss at the working current rather than on the label.