VBP165I75
Product Specifications
VBP165I75
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBP165I75 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBP165I75: a 650 V field stop IGBT with the diode in the same TO247
The VBP165I75 is an insulated gate bipolar transistor with a fast recovery diode in the same TO247 body. The vendor table prints a collector to emitter rating of 600 to 650 V, plus or minus 30 V on the gate, a 5 V gate threshold, 75 A of collector current, a saturation voltage of 2 V at a 15 V gate, and a field stop structure. The diode is part of the package rather than a second line item on the bill of materials, which is the reason this class is bought as one code.
Field stop is the structure that replaced the older punch through die in this voltage class. A thin n drift region carries the voltage, a field stop layer at the back stops the space charge from reaching the collector, and the result is a saturation voltage that does not climb as steeply with current as a planar IGBT of the same area. The 2 V figure is what makes the part usable at 40 to 75 A, because at 5 V saturation the same die would be a heater.
An IGBT is the right switch here for one reason: at 650 V and 75 A the conduction loss of a MOSFET is dominated by the drift region, and a bipolar carrier injection removes most of that resistance. The trade is a slower turn off and a tail current that a MOSFET does not have. On a 16 to 20 kHz switching rail the tail is small against the period. On a 100 kHz rail it is not, so the switching frequency decides whether this part is the correct answer.
Key data for the VBP165I75
| Configuration | Single IGBT with a co-packaged fast recovery diode |
| Package | TO247, through hole, tab on the collector |
| VCE | 600 V to 650 V |
| VGE | Plus or minus 30 V |
| VGE(th) | 5 V |
| ICE | 75 A |
| VCE(sat) | 2 V at a 15 V gate |
| Structure | Field stop |
| Diode | Fast recovery, in the same body |
| Gate drive | 15 V on, minus 5 to minus 8 V off is the usual choice |
| Conduction at 37 A | 74 W from the saturation voltage alone |
| Conduction at 75 A | 150 W from the saturation voltage alone |
What a 650 V rating covers
The 650 V class is the workhorse of single phase offline power. A 230 V mains input rectifies to a 325 V DC bus, and a boost stage in continuous conduction puts the switch node at the bus plus the diode drop, so 400 to 420 V is the steady state. A lightning surge test at 2 kV applied through the input filter adds another 100 to 150 V of clamp. That leaves 650 V parts with a working margin near 1.5 and a surge margin near 1.25, which is the reason the class exists rather than 500 V or 800 V.
Three phase input at 400 V rectifies to 565 V DC, and that is where the 650 V part runs out of headroom. A 400 V three phase bus wants 900 V or 1200 V, and putting a 650 V part there works only until the first regeneration event on the line. If the board is fed from a single phase line with a power factor stage, this part is in its class.
The sourcing side of a 650 V IGBT is narrower than the MOSFET side, because fewer lines make a co-packaged diode die. Buyers who need a second source on a 20 kW stage of this class usually plan it before the first build, not after. Where the same board has to keep running when one line stops, the how to reduce component cost page covers how a converter is re-quoted without giving up the voltage margin.
Losses and the TO247 thermal path
At 2 V saturation and 75 A the die makes 150 W before switching. At 50 A it makes 100 W, at 37 A 74 W, and at 20 A 40 W. The TO247 tab is about 1.5 square centimetres of copper on the back of the die, with a junction to case resistance in the region of 0.5 to 1 K per watt depending on the die area inside the body. At 74 W and 1 K per watt the case has to sit at 60 C to keep the junction at 135 C, and that is a case temperature no natural convection heatsink reaches.
So the working current is not 75 A. On a heatsink held at 80 C with 0.5 K per watt, 74 W puts the junction at 117 C and the part is inside its limit at 37 A. At 75 A the same heatsink leaves the junction at 155 C, which is past the usual 150 C ceiling. The honest reading is that this body carries 35 to 45 A continuous in a fan cooled converter and 25 to 30 A on a natural convection plate.
The diode carries the same current during the dead time and during the freewheel interval. Its forward drop at 40 A is around 1.5 to 1.8 V for a fast recovery die at 650 V, so the freewheel loss is 60 to 72 W at 40 A and duty matters more than the on state figure. A converter that runs at 0.4 duty puts most of the loss in the switch, and one at 0.8 duty puts it in the diode.
Where this part fits
Induction heating is the classic application. A series resonant inverter at 20 to 40 kHz drives a coil through this switch and its diode, the bus is 300 to 400 V from a single phase rectifier, and the current is 25 to 40 A. The tail current at that frequency adds roughly 10 percent to the switching loss against a MOSFET, and the 2 V saturation saves more than that against a 650 V MOSFET at the same current.
Welding inverters at 20 kHz, uninterruptible power stages at 400 V, and the power factor front end of a 3 to 6 kW charger all sit in the same window. Motor drives at 380 to 400 V AC are usually 1200 V territory because of the reflected surge, so this part is not the first pick there.
On a board that already runs a 650 V MOSFET, the swap to an IGBT changes the gate drive: 15 V on and a negative off bias are needed for clean turn off, and the 5 V threshold means a 10 V gate leaves the part half on. Plan the driver before the part is committed.
The sourcing side of this part is covered on the incoming inspection plan. For a co-packaged part bought in volume, that page covers what is measured on each lot before it reaches the line.
Questions we get on this code
Is the diode really inside the package? Yes, the table lists the configuration as IGBT with a fast recovery diode, and the third pin is the emitter with the diode anode on the same node. A board that expects a separate diode can still use the part and simply leave the external one unpopulated.
Can it replace a 600 V MOSFET directly? Electrically the voltage class fits, but the drive does not. A MOSFET gate at 10 V is fully on, while this part needs 15 V for the printed saturation figure and a negative bias to turn off in under a microsecond.
What is the switching frequency ceiling? The tail current sets it. At 20 kHz the tail adds a few watts. At 60 kHz it is 20 to 30 W at 40 A, which is the point where a silicon carbide part starts to win on total loss even at three times the price.
How is the date code read? The body is laser marked with the code and the lot, and the marking is the only place the date lives. A lot that arrives without a readable marking is a lot to hold at goods inwards.