VBP112MC30
Product Specifications
VBP112MC30
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBP112MC30 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBP112MC30: 1200 V and 30 A silicon carbide in a TO247
The VBP112MC30 is a single N channel silicon carbide MOSFET in a TO247 body. Drain to source is 1200 V, the gate window is minus 10 V to plus 22 V, the threshold is 2 to 4 V, the printed drain current is 30 A and the on resistance is 80 milliohm at an 18 V gate. The structure is listed as SiC-S.
The gate window is the first thing to read. Minus 10 V to plus 22 V is not the plus or minus 20 V of a silicon part: the positive side is rated to 22 V because the recommended on drive is 18 V, and the negative side stops at 10 V because the gate oxide does not take more. A driver built for silicon and set to 20 V on and minus 5 off sits inside the window, but a driver that rings to 24 V on a fast edge does not.
The on resistance is quoted at 18 V for a reason. At 15 V the channel is not fully enhanced and the resistance is higher, often by 30 to 50 per cent, so a 15 V driver gives more loss than the table suggests. This is the opposite of the silicon parts in this catalogue, where 10 V is the reference and 4.5 V is the weaker column.
Key data for the VBP112MC30
| Configuration | Single N channel |
| Package | TO247, bolted to a heatsink |
| VDS | 1200 V |
| VGE | Minus 10 V to plus 22 V |
| Vth | 2 to 4 V |
| ID | 30 A, a die figure at a 25 C case |
| RDS(on) at 18 V | 80 milliohm |
| Technology | Silicon carbide |
| Loss at 5 A | 2 W |
| Loss at 10 A | 8 W |
| Loss at 15 A | 18 W |
| Loss at 30 A | 72 W |
What silicon carbide buys at 1200 V
At 1200 V a silicon superjunction part is not available in a useful resistance, so the choice is between an IGBT and a silicon carbide MOSFET. The IGBT has a fixed forward drop of about 2 V at 25 C, so at 5 A it dissipates 10 W and at 15 A it dissipates 30 W. This part at 80 milliohm dissipates 2 W at 5 A and 18 W at 15 W, and it does so without the tail current that makes an IGBT lose at every turn off.
The advantage grows with frequency. An IGBT at 20 kHz with a 3 microsecond tail loses several watts per cycle at 15 A; a SiC MOSFET has no tail, and its switching loss is set by the charge on the output capacitance and the gate charge. That is why a 1200 V SiC part makes a 50 kHz converter practical where an IGBT would need a much larger heatsink.
The price is on the gate and on the diode. A SiC MOSFET needs 18 V on and a negative bias off, its gate oxide is thinner for the same threshold, and its body diode has a forward drop of about 4.5 V at rated current, which is high enough that the diode is not a useful freewheel path in a bridge leg. In a bridge the body diode conducts only in the dead time, and an external SiC Schottky is often placed in parallel to carry the freewheel current.
Resistance that rises with temperature
A silicon trench MOSFET at 100 V has a resistance that roughly doubles from 25 C to 125 C. A SiC MOSFET has the same direction and a similar factor, about 1.6 to 2, and the printed 80 milliohm is a 25 C figure. At 125 C the working resistance is 130 to 160 milliohm, so the loss at 15 A is 29 to 36 W rather than 18 W.
That changes the thermal plan. A converter sized on the 25 C figure will run hot, and the positive temperature coefficient that makes paralleling easy also means the loss does not arrest itself. Two devices in parallel share current reasonably well at 1200 V because the hotter one has the higher resistance, which is the reason a 60 A load is often built as two 30 A parts rather than one.
Switching loss per cycle is the other term. At 1200 V the energy in the output capacitance is proportional to the square of the voltage, and at 50 kHz it can be a few watts even at 10 A. Soft switching, or a topology that turns on at zero voltage, removes most of it and is the reason SiC and a resonant topology are often used together.
Where the part fits and where it does not
It fits a 800 V DC bus in a three phase inverter, a 690 V drive, a solar string inverter at 1000 V, a charger for an 800 V battery, a power factor stage at high voltage and an induction heating supply. It does not fit a 400 V bus where a 650 V silicon part is cheaper, a 30 A continuous load in a TO247 without a good sink, or a driver that cannot supply 18 V on and a negative off bias.
Where a 1200 V part replaces an IGBT, the gate drive, the dead time and the freewheel path all change, and the replacement is a circuit change rather than a part swap. Our strategic sourcing page covers how a high voltage family is qualified and held when the supply is narrow.
The sourcing side of this part is covered on the component obsolescence management. For a 1200 V die in a long life product, that page covers how the supply is watched before the family narrows.
Questions we get on this code
Can it be driven at 15 V? It can, and the resistance will be higher than the printed 80 milliohm. The table figure applies at 18 V, which is the recommended drive.
Is negative bias required? Not for turn on. It is required in a bridge at high dv/dt, and the window allows down to minus 10 V.
Why is the body diode drop so high? It is a property of the SiC junction. In a bridge an external SiC Schottky is normally placed across it for the freewheel current.
What does the order carry? Part number, TO247, and tube packing. We confirm the packing and the date code on the offer.