VBMB16R20SFD
Product Specifications
VBMB16R20SFD
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBMB16R20SFD from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBMB16R20SFD: 600 V, 0.175 ohm and a fast diode claim the table does not repeat
The VBMB16R20SFD is the fast diode member of the 600 V family, in the TO-220F isolated body, with 0.175 ohm at a 10 V gate and a 20 A continuous rating at a 25 C case. It is the part a buyer reaches for when a 600 V stage has to commutate hard and the plain member is too slow, so the diode row carries the decision.
On this sheet the diode row reads 475 ns. That is the same figure the plain VBMB16R20S prints, and the same charge of 5.8 microcoulomb and the same 30 A of peak reverse current. The features list on page one says ultra fast body diode; the electrical table does not show a faster recovery than the non FD sibling. The one member of the family that does print a fast diode is the 650 V VBMB165R42SFD at 90 ns.
That gap is worth stating plainly because it changes what the part can be used for. A customer who orders this string expecting a 90 ns diode and measures 475 ns on the bench has a right to ask, and the answer has to come from the vendor's test report, not from a comparison table.
The parameter table in full
| Drain to source voltage at maximum junction temperature | 600 V |
| Gate to source voltage, continuous | plus or minus 30 V |
| On resistance at 10 V gate and 6.5 A, 25 C | 0.175 ohm typical |
| Gate threshold at 250 microamp | 2.5 V minimum, 4.5 V maximum |
| Continuous drain current, case at 25 C and 100 C | 20 A and 12 A |
| Pulsed drain current, repetitive | 60 A |
| Single pulse avalanche energy, 28.2 mH and 10 A start | 980 mJ |
| Maximum power dissipation, case at 25 C | 120 W |
| Linear derating factor | 1.67 W per C |
| Junction to case and junction to ambient | 0.57 and 62 C per watt |
| Operating junction and storage range | minus 55 to plus 150 C |
| Drain source voltage slope, junction at 125 C | 50 V per ns |
| Reverse diode voltage slope | 15 V per ns |
| Input, output and reverse transfer capacitance | 2300, 80 and 4 pF |
| Effective output capacitance, energy and time related | 63 and 213 pF |
| Gate source and gate drain charge | 15 and 19 nC |
| Total gate charge | not printed on this sheet |
| Turn on delay and rise time at 520 V and 8 A | 18 and 24 ns typical, 25 and 55 ns maximum |
| Turn off delay and fall time, same conditions | 80 and 12 ns typical |
| Gate input resistance | 0.8 ohm |
| Continuous and pulsed source drain diode current | 20 and 60 A |
| Body diode forward drop at 8 A | 1.5 V maximum |
| Body diode recovery time, charge and peak current | 475 ns, 5.8 microcoulomb and 30 A |
| Forward transconductance at 6.5 A | 5.6 S |
| Peak soldering temperature for 10 s | 260 C |
Thermals: 120 W on the tab against 62 C per watt in air
The 120 W row assumes a 25 C case. The ambient row is 62 C per watt, so a board in still air removes 2.02 W for the full 125 C rise, which through 0.175 ohm is 3.4 A at a 25 C ambient and 3.03 A at 50 C. At the 20 A rating the channel sheds 70 W and needs a case below 110 C through the 0.57 C per watt path, which is a real heatsink.
The isolated body is the reason the dissipation row stops at 120 W while the 650 V sibling prints 210 W. The moulded tab adds a thermal layer between the die pad and the heatsink surface, so the same die that passes 210 W through an exposed tab passes 57 percent of that here. Anyone comparing the two sheets side by side has to compare the number that belongs to the body they will buy.
A useful sanity check for a customer: at 8 A, which is the current where on resistance is specified, the loss is 11.2 W. That is above the still air budget and inside the heatsink budget, so the part belongs on metal in any board that runs at its specified current, and the 20 A row on page one is only reachable with a heatsink that holds the case near room temperature.
Gate charge is missing, and that has a cost
The total gate charge cell on this sheet is empty. The gate source charge of 15 nC and the gate drain charge of 19 nC are printed, but without the total the drive loss cannot be computed from the sheet alone. The plain 600 V member prints 48 nC typical and 96 nC maximum at the same test conditions, so the working assumption is that this die carries the same gate, but an assumption is not a specification.
When a driver is sized from a missing row, the usual error is to take the gate source and gate drain charges, add them and stop at 34 nC. That figure leaves out the charge that goes into the output capacitance during the drain swing, which on a super junction device of this size is most of the total. The result is a driver that looks adequate on paper and gets hot in the second hour.
The switching rows do not fill the gap either: 18 ns and 24 ns at 520 V and 8 A into a 9.1 ohm resistor describe the part, not the drive. Ask the supplier for the gate charge curve before a driver is committed, and measure one lot if the schedule allows.
Where it fits, and where it should not go
The 260 C soldering row and the 20 A rating put this part in reflowed modules and in supplies where the switch sits on a heatsink with an insulating interface. Lighting and industrial supplies are the stated targets, and a ballast running at 40 kHz to 60 kHz with a hard commutated half bridge is the natural circuit.
It should not go into a continuous conduction PFC that runs at 100 kHz with a silicon carbide diode, or into a synchronous bridge where the body diode conducts every cycle. In both cases a 475 ns recovery dominates the loss budget, and the FD suffix will not change it. Where a genuinely fast diode is needed, the 650 V VBMB165R42SFD prints 90 ns in the same body and costs about a third more resistance.
Where a customer is consolidating a bill of materials from several 600 V switches, the family view helps: the same body, the same gate and the same threshold window across the 600 V members, with on resistance from 0.15 to 0.175 ohm and avalanche energy from 485 mJ to 980 mJ. Our cross reference work for power parts treats the diode recovery and the avalanche row as the two that must match before a consolidation is proposed.
Questions we answer before a reel is booked
First, the diode. Ask for the recovery test conditions, not just the number. 475 ns at 8 A forward and 400 V reverse with 100 A per microsecond is the printed condition, and a bench measurement at a different di/dt will disagree. If the circuit needs a genuine fast diode, this string is not it.
Second, the gate charge. The empty cell is the only row on the sheet that a driver cannot do without. Have the supplier send the curve, and compare the plateau voltage against the driver's output, since a 4.5 V maximum threshold leaves little margin for a 6 V rail that sags.
Third, the body and the second source. A 600 V 0.175 ohm part in a Fullpak is available from several suppliers, and the diode recovery varies by a factor of five between them. The lead time work and our incoming inspection plan both keep the recovery and the avalanche row on file for each approved alternate, so a lot that measures outside the window is caught before it reaches the line.