Contact Us

VBMB165R36S

Brand: VBsemi
VBsemi VBMB165R36S is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBMB165R36S — Discrete & Power Semiconductors | Superb Automation

VBMB165R36S

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBMB165R36S from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBMB165R36S: 650 V super junction in the full pack body

The VBMB165R36S is a 650 V N channel super junction MOSFET in the TO-220F full pack body, the isolated tab version, with 0.075 ohm at a 10 V gate, 76 nC of total gate charge and 36 A of continuous drain current with the case at 25 C. The application list is the standard 650 V one: server and telecom supplies, switch mode supplies, power factor correction, lighting ballast and industrial drives.

The full pack is the point of this order string. A TO-220F has a moulded body over the tab, so the tab is isolated and can be mounted straight to a shared heatsink without a pad. That removes a washer from the bill and, more importantly, removes the thermal resistance of the pad from the stack, which in a 30 W part is the difference between a 100 C junction and a 115 C one.

The electrical table is the familiar super junction set: 1400 mJ class avalanche, 50 V per ns drain source slope, a 4 pF reverse transfer capacitance and a 475 ns body diode recovery, which is the slowest diode in this shipment and the row to read before a bridge is considered.

The parameter table

Drain to source voltage650 V
Gate to source voltageplus or minus 30 V
On resistance at 10 V gate, 12 A, 25 C0.075 ohm typical
Gate threshold at 250 microamp2.5 V to 4.5 V
Continuous drain current, case at 25 C and 100 C36 A and 22 A
Pulsed drain current110 A
Single pulse avalanche energy, 28.2 mH, 18 A start1300 mJ
Power dissipation, case at 25 C210 W
Junction to case and junction to ambient0.7 and 62 C per watt
Linear derating factor1.67 W per C
Operating junction and storage rangeminus 55 to plus 150 C
Breakdown voltage temperature coefficientminus 0.70 V per C
Zero gate voltage drain current at 650 V1 microamp maximum
Zero gate voltage drain current at 520 V, 125 C100 microamp maximum
Input, output and reverse transfer capacitance3800, 80 and 4 pF
Effective output capacitance, energy and time related63 and 213 pF
Total gate charge at 520 V, 8 A76 nC
Gate source and gate drain charge15 and 19 nC
Turn on delay and rise time18 and 24 ns typical
Turn off delay and fall time80 and 12 ns typical
Gate input resistance0.8 ohm typical
Body diode forward drop at 8 A1.5 V maximum
Body diode recovery time and charge475 ns and 5.8 microcoulomb
Body diode peak reverse recovery current35 A
Drain source voltage slope at 125 C50 V per ns

The thermal pair inside a moulded body

0.7 C per watt from junction to case is the value printed for the bare tab parts in this family, and it is printed here for a full pack body. A moulding and an isolation layer normally add between 0.3 and 1.0 C per watt, so this row deserves a measurement on the qualification sample before a heatsink is sized. If the real figure is 1.3 C per watt, a 30 W load that was sized at a 21 C rise runs at 39 C, and the 150 C junction arrives 18 C earlier than the calculation said.

The 210 W dissipation row is 31 W above the 178.6 W that 0.7 C per watt supports at a 150 C junction with a 25 C case. As with the other sheets in this band, the thermal pair is the limit and the dissipation row is a package capability. At 36 A through 0.075 ohm the die dissipates 97 W, which needs the case held near 75 C, and that is a heatsink rather than a pad.

In still air the part sees 62 C per watt, which supports 2.02 W at a 25 C ambient and 1.61 W at 50 C, equal to 5.18 A and 4.64 A. For a 400 V bus auxiliary supply drawing 1 A, the loss is 0.075 W and the part runs cold. For a 5 A load in still air the loss is 1.88 W and the junction sits about 117 C above the ambient, which is the edge of the limit at 50 C.

The 475 ns diode, and where it is acceptable

475 ns of recovery with 5.8 microcoulomb of charge and 35 A of peak reverse current is the slowest body diode in this shipment, and it is slow for a super junction part. In a continuous conduction power factor stage the switch body diode never conducts, so the row costs nothing. In a bridge, a phase shifted converter or a synchronous rectifier position, the diode conducts every cycle and 5.8 microcoulomb at 400 V of reverse bias is energy the opposite switch has to absorb. At 65 kHz that is 0.38 W per switching cell before the current spike is counted, which is my arithmetic on the printed charge and bus voltage, not a printed loss figure.

The peak reverse current is the other half. 35 A of reverse current through 20 nH of loop inductance produces a voltage step of about 0.7 V per nanosecond of transition, which a 400 V bus tolerates and a 650 V part tolerates less well when the bus is already at 410 V. Measure it on the first article rather than trusting the nominal.

The 50 V per ns drain source slope is fast, and with an 80 ns turn off delay and a 12 ns fall the EMI signature is decided by the gate resistor and the snubber, not by the part. A resistor copied from a slower part will produce a ringing edge at 650 V, which is the kind of thing that passes on the bench and fails in a cabinet.

Where the full pack earns its cost

A shared heatsink with several live tabs needs either isolated pads or isolated bodies. The pads add 0.5 to 1.0 C per watt and a assembly step, and they are the part that fails a hipot test when the burr is left on the hole. A full pack body removes both, at the price of a body a little wider than the bare tab part and a thermal path that has to be measured rather than assumed.

On a 400 V bus at 5 A to 15 A this part is the right current class: 0.075 ohm gives 1.9 W at 5 A and 16.9 W at 15 A, and the second number needs the heatsink. Above 20 A the 0.062 ohm 600 V sibling is the better economic choice and only if 600 V leaves enough margin on the surge.

Where a customer is second sourcing a 650 V full pack part, the two rows that differ most between suppliers are the body diode recovery and the junction to case figure inside the moulding. Our kitting service keeps the bodies separated by part number so a bare tab and a full pack cannot be mixed on one line, and the supplier scorecard records the measured case resistance rather than the printed one.

The 1300 mJ avalanche figure comes from a 28.2 mH load with an 18 A start, which is a large single event energy for a full pack body. It covers the leakage spike of a flyback transformer at these power levels without a clamp, and it does not cover a repeated event. Where a supply sees the same surge on every start, the row to use is the 1.67 W per C derating factor and a measured tab temperature, and the clamp belongs on the board.

Questions before a reel is booked

First, the junction to case figure inside the full pack body. 0.7 C per watt is the bare tab value, so ask for the measured number before the heatsink is sized.

Second, the diode. If the topology forces the body diode to conduct, 475 ns and 35 A of peak reverse current have to be measured hot, because both rise with temperature.

Third, the mounting. The full pack is bolted, not clipped, and the torque and the thermal compound matter as much as the part. The cost work counts the pad and the washer that the full pack removes, because the cheaper part is not always the cheaper assembly.