VBM16I20
Product Specifications
VBM16I20
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBM16I20 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBM16I20: a 600 V field stop IGBT in TO220
The VBM16I20 is an insulated gate bipolar transistor with a co-packaged fast recovery diode in a TO220 body. Collector to emitter is 600 V with 650 V at the top of the class, gate to emitter is plus or minus 30 V, the gate threshold is 5 V, rated collector current is 20 A and saturation is 1.65 V with 15 V on the gate. The die is a field stop part.
Field stop is the structure that replaced the older non punch through die in this class. It puts a heavily doped layer at the back of the drift region so the field stops there rather than reaching the collector, which lets the drift region be thinner for the same voltage and lowers the saturation voltage and the tail current.
The saturation of 1.65 V is lower than the 1.9 V part in the surface mount body in this band, which is what the newer die buys. At 10 A that is 16.5 W instead of 19 W, and at 20 A it is 33 W instead of 38 W. The difference is small per device and large across a production run.
Key data for the VBM16I20
| Package | TO220 through hole with a metal tab |
| Configuration | IGBT with a co-packaged fast recovery diode |
| VCE | 600 V, printed as 600/650 at the top of the class |
| VGE | Plus or minus 30 V |
| VGEth | 5 V, which is not a logic level gate |
| ICE | 20 A rated collector current |
| VCEsat at 15 V | 1.65 V |
| Technology | Field stop |
| Loss at 5 A | 8.25 W at 1.65 V |
| Loss at 10 A | 16.5 W at 1.65 V |
| Loss at 20 A | 33 W at 1.65 V |
| Gate drive needed | 15 V on, with a hard pull down or a small negative bias off |
Field stop and the tail current
An IGBT turns off in two parts. The first is the channel, which stops conducting as the gate falls. The second is the stored charge in the drift region, which continues to flow as a tail that decays over a few microseconds. That tail is pure loss, and it is the reason an IGBT has a switching loss that a MOSFET of the same voltage does not.
A field stop die has a thinner drift region and a back layer that injects less charge, so the tail is shorter and the turn off loss is lower than on an older die. That is what makes a 20 kHz to 30 kHz converter practical with this class of part.
The tail does not go away. At 20 A and 400 V a tail of a couple of microseconds at 30 kHz is a few watts, which sits on top of the conduction loss. Below 15 kHz it is small, and that is why these parts are used in induction heating, welders and low frequency drives rather than in compact chargers.
Saturation on 15 V of gate drive.
The gate threshold of 5 V means the part needs a real driver and a 15 V rail. The saturation figure is quoted at 15 V for that reason: at 10 V the device is not fully enhanced and the saturation is higher. A driver built for a MOSFET at 10 V would leave this part hotter than its table suggests.
The plus or minus 30 V gate window is generous and it allows a minus 8 V off bias without stress, which is what a bridge leg wants. A negative bias also reduces the turn off loss, because the gate discharges faster through a larger voltage step.
The co-packaged diode is part of the product. On a 600 V part the diode recovery is the main source of loss in the opposite device at every commutation, and its softness decides how much of that loss turns into a voltage spike as well as heat. A snubber across the switch is often cheaper than a faster diode.
Heat removal in a TO220 at 1.65 V
At 10 A the part makes 16.5 W. A TO220 tab on a clip on heatsink with a silicone pad holds that with a case about 20 degrees above the heatsink. At 15 A it makes 24.75 W and the heatsink has to be larger, and at 20 A it makes 33 W and the part wants a TO247 or a heatsink with airflow.
The tab is the collector and it sits at the bus voltage, so the heatsink is live unless insulated. At 400 V that is a safety item, and the insulator has to be rated for the voltage as well as for the heat. A shoulder washer and a mica or silicone pad are the usual arrangement.
The junction to case resistance of a TO220 is about one degree per watt, so 16.5 W gives a case 16 degrees above the heatsink before the insulator is counted. That is the number that decides whether the product has margin on a hot day in a closed enclosure.
Where the part fits and where it does not
It fits a 230 V front end at 5 to 10 A, an induction heating driver below 30 kHz, a small welder, a brake chopper and a low frequency inverter leg. It does not fit a 100 kHz converter, a 480 V AC input, or a load above about 12 A in this package without a large heatsink.
For a front end at this voltage the questions are the saturation at the working current, the tail loss at the frequency and the isolation of the heatsink. Our NPI production launch checklist page lists what has to be settled before a new build with a part like this goes to the line.
The sourcing side of this part is covered on the component lead time solutions. For an IGBT bought ahead of a build, that page covers how the lead time is planned rather than discovered.
Questions we get on this code
Can the gate be driven from a 12 V rail? It can, at a higher saturation than the published 1.65 V, which is quoted at 15 V. A 15 V rail with a dedicated driver is the right arrangement.
Is 20 A continuous? At 33 W in a TO220, no. Eight to twelve amps on a clip on heatsink is realistic.
What is the difference from the 1.9 V part? A newer die with a thinner drift region and a shorter tail. The conduction loss is about 13 per cent lower and the turn off loss is lower too.
What should a purchase order carry? Part number, TO220, and the packing the line can take. We confirm the tube quantity on the offer.