VBM165R04
Product Specifications
VBM165R04
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBM165R04 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBM165R04: 650 V and 4 A at 2200 milliohm
The VBM165R04 is a single N channel MOSFET in a TO220 body rated at 650 V drain to source, plus or minus 30 V on the gate, a 3.5 V threshold, 4 A of drain current and 2200 milliohm at a 10 V gate. The die is planar.
This is a small current part with a large voltage rating, the kind used for the housekeeping side of a high voltage product: a start up circuit, a bias supply, an auxiliary converter on a 400 V bus. It is not a power switch for the main path, and the resistance makes that clear.
At 4 A the loss is 35 W. At 2 A it is 8.8 W. At 1 A it is 2.2 W. At 0.5 A it is 0.55 W. The working current is under an amp, and at that point the part is a useful high voltage switch in a package that can hold it.
Key data for the VBM165R04
| Configuration | Single N channel |
| Package | TO220 through hole with a metal tab |
| VDS | 650 V |
| VGS | Plus or minus 30 V |
| Vth | 3.5 V |
| ID | 4 A, a die figure at a 25 C case |
| RDS(on) at 10 V | 2200 milliohm |
| Technology | Planar |
| Loss at 0.5 A | 0.55 W at 2200 milliohm |
| Loss at 1 A | 2.2 W at 2200 milliohm |
| Loss at 4 A | 35 W at 2200 milliohm |
| Gate drive | 10 V; the 3.5 V threshold rules out a 5 V logic level for any real current |
Why the resistance is so high at this current
A planar die at 650 V gives up resistance for a breakdown that is stable and predictable, and a small die gives up area. The two together give 2200 milliohm, which is a thousand times the resistance of a 40 V part in the same package. The current label of 4 A is a die figure at a case this body does not reach at 35 W.
The trade is deliberate. An engineer who needs a few hundred milliamps at 400 V does not want to pay for a 100 milliohm die that is ten times the area and several times the price. The small die also has lower capacitance, which is a real advantage in a high voltage switching node.
Where the product needs more current at this voltage, the answer is the charge balance parts in the 600 V and 700 V classes, which reach 80 to 200 milliohm. This part sits below them in current and above them in ruggedness per unit area.
Start up circuits and bias supplies.
The classic use is a start up circuit that has to hold a 400 V bus while a controller wakes. The switch is on for a short period at a fraction of an amp, and the loss is under a watt, so a small die with a high voltage rating is exactly right.
The other use is a bias winding switch or an auxiliary flyback that runs at a few hundred milliamps. In both cases the part is on for a long time and off for a short one, so the conduction loss is the one that matters and the switching loss is small.
At 650 V the drain sees the bus plus the reflected voltage plus the leakage spike in a flyback, so the class has to cover the sum. On a 400 V bus with a 100 V reflected voltage and a 100 V spike the sum is 600 V, which is inside 650 V with 50 V of margin. A larger spike needs a clamp.
Creepage and the tab at 650 V
A TO220 pin pitch is 2.54 mm, and at 650 V the creepage between the drain tab and the gate lead is marginal for a polluted environment. A coated board or a conformal coat is the usual answer, and the board should keep the high voltage node away from the low voltage side of the package.
The tab is the drain at the bus voltage, so a heatsink is live unless insulated. At the loss levels this part runs at, a heatsink is rarely needed: at 0.5 A the loss is 0.55 W, which the tab alone removes. That is one of the attractions of a small die in a large package.
The gate drive at 10 V is easy to provide from a small isolated supply, and the 30 V window is generous. What matters more is the pull down, because at 650 V the leakage from drain to gate can charge a floating gate and leave the part half on in a circuit that is supposed to be off.
Where the part fits and where it does not
It fits a high voltage start up circuit, an auxiliary flyback at a few hundred milliamps, a bias supply on a 400 V bus, a discharge path at low current and a clamp switch. It does not fit a main power path at amps, a 1000 V string, or a product that needs a low resistance at 650 V.
For a small part in a high voltage position the questions are the sum of bus and spike, the creepage the product claims and the availability of a second source. Our excess inventory management page covers how a part held for a long life build is kept and how its age is handled.
The sourcing side of this part is covered on the material requirements planning. For a small high voltage part on a long schedule, that page covers how the demand is carried against the build plan.
Questions we get on this code
Can it carry 4 A? At 35 W, no. Under an amp it is comfortable. The 4 A label is a die figure.
Why is the resistance so much higher than a 600 V part? A planar die and a small area. The part is built for voltage and for low capacitance, not for current.
Does it need a heatsink? At the currents it is used at, no. The tab alone removes the loss, which is one reason the package is bigger than the die needs.
What should a purchase order carry? Part number, TO220, and the packing the line can take. We confirm the tube quantity on the offer.