VBED1402
Product Specifications
VBED1402
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBED1402 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBED1402: a 40 V N channel at 1.6 milliohm in a leadless body
The VBED1402 is an N channel trench MOSFET in the SOT-669 outline, printed at 40 V from drain to source with plus or minus 20 V on the gate. On resistance is 0.0016 ohm typical at a 10 V gate with 30 A flowing and 0.0020 ohm at a 4.5 V gate with 20 A, continuous drain current is 100 A with the case at 25 C, 29 A on a 10 second pulse with the ambient at 25 C and 23 A with the ambient at 70 C, and the pulsed rating is 250 A. Gate charge is 50 nC typical at a 10 V gate, and the junction to case figure is 0.33 C per watt typical.
One point six milliohm is the lowest resistance in this band and it comes with a 110 A package limitation in the vendor's own note, which sits above the 100 A current row and is the kind of arithmetic a buyer should read twice. The part is built for synchronous rectification and for power supply output stages where the load current is between 20 A and 60 A and the loss budget is almost entirely conduction loss.
The ratings a buyer checks first
| Drain to source voltage | 40 V |
| Gate to source voltage | plus or minus 20 V |
| On resistance at 10 V gate, 30 A | 0.0016 ohm typical |
| On resistance at 4.5 V gate, 20 A | 0.0020 ohm typical |
| Continuous drain current, case at 25 C and 70 C | 100 A and 80 A |
| Continuous drain current, 10 second pulse, ambient at 25 C and 70 C | 29 A and 23 A |
| Pulsed drain current | 250 A |
| Avalanche current and energy | 80 A, 320 mJ into 0.1 mH |
| Power dissipation | 312 W at 25 C case, 3.13 W at 25 C ambient |
| Junction to ambient, steady state | 32 C per watt typical, 40 maximum |
| Junction to case | 0.33 C per watt typical, 0.4 maximum |
| Gate threshold voltage | 1.2 V minimum, 2.5 V maximum |
| On state drain current at 5 V and 10 V gate | 120 A |
| Total gate charge at 10 V gate and 20 V drain | 50 nC typical, 90 nC maximum |
| Input, output and reverse transfer capacitance | 4500, 550 and 350 pF |
| Turn on delay and rise time at 10 V gate | 20 and 11 ns typical |
| Body diode forward voltage at 20 A | 0.8 V typical, 1.2 V maximum |
| Junction and storage range | minus 55 to plus 150 C |
Reading the electrical table instead of the front page
The current rows do not agree with the package note and the buyer should notice. The table prints 100 A at a 25 C case and footnotes it as calculated from the maximum junction temperature, while a separate note says the package limitation current is 110 A. On most parts the package limit is the smaller number and here it is the larger one, which means the 100 A row is a thermal calculation rather than a package capability. Either way the ambient rows are the ones that describe a real board, and 29 A on a 10 second pulse is the figure to plan with.
The resistance and the current do not meet either. One hundred amps through 0.0016 ohm is 16 W, which the 312 W case figure would allow but no leadless pad would remove. At 30 A the loss is 1.44 W, at 40 A it is 2.56 W, and the 32 C per watt junction to ambient path supports 2.8 W from a 60 C ambient to a 150 C junction. That puts the honest continuous current near 40 A on a good pad, which is still substantial and is where the part should be used.
The two switching blocks show how much the drive voltage matters on a die this large. With a 10 V gate the turn on delay is 20 ns, the rise time 11 ns, the turn off delay 77 ns and the fall time 10 ns. With a 4.5 V gate the same rows read 102, 62, 180 and 60 ns, and the turn off delay more than doubles. For a synchronous rectifier driven from the same 5 V rail as the logic, that is the difference between a clean dead time and a body diode conduction interval at every switching edge.
The body diode is the row that decides a synchronous rectifier. Forward drop is 0.8 V at 20 A, recovery is 50 ns typical and 75 maximum, and the recovered charge is 70 nanocoulomb typical and 105 maximum, with a 30 ns fall and a 20 ns rise in the recovery waveform. In a 40 V output stage the diode conducts during the dead time and its forward drop sets the loss in that interval, so a part with a 1.2 V maximum at 20 A loses 24 W while the channel is off if the dead time is long. That is the reason the 4.5 V drive rows matter more than the resistance row on a converter.
Where a 40 V N channel at 1.6 milliohm earns its place
The first case is a synchronous rectifier on a 12 V output, where 40 V covers the ringing and 0.0016 ohm makes the conduction loss negligible at 30 A. The second is a battery protection switch in a 24 V pack, where two of these in series still give 3.2 milliohm and the 320 mJ avalanche rating covers a cable event. The third is a hot swap or load switch on a 12 V rail, where the 250 A pulse covers a disk drive or a fan inrush and the 40 C per watt steady state path keeps a 25 A load inside the junction limit.
It is a poor choice for a 48 V rail, where 40 V leaves no margin for a regenerating load, and for a high frequency bridge, where 4500 pF of input capacitance and 550 pF of output capacitance need a driver and a dead time that a 1.6 milliohm part makes expensive. The part is built to be a switch in a low voltage, high current path and not a switching element at 200 kHz.
Sourcing notes and the second source question
At this resistance the second source question is a die size question, and a substitute that prints 0.002 ohm will have a different input capacitance, a different diode and often a different pad pattern. Our pin to pin cross reference keeps the capacitance, the diode rows and the thermal resistance beside the resistance, so a substitution is not sold on one number that the board cannot use.
On cost, a 1.6 milliohm part is the expensive end of the 40 V band and the arithmetic of whether it pays is worth doing before a board revision. How to reduce component cost sets out the comparison against a 2.5 milliohm part, including the case where the cheaper die costs more in copper area and in heat than it saves on the unit price.
Questions we answer before a reel is booked
The first question is whether 100 A is a real figure. It is a thermal calculation at a 25 C case, the package note says 110 A, and a 1 inch pad in 60 C air carries about 40 A continuously. The second is whether the part works on a 5 V drive. It does, at 0.0020 ohm and with switching times roughly three times longer than at 10 V, which is acceptable for a load switch and marginal for a synchronous rectifier at high frequency.
The third question is about dead time. The body diode at 0.8 V and 20 A is 16 W during the interval it conducts, so a converter that leaves a long dead time will lose more there than it saves on resistance. The fourth is about the avalanche rating: 320 mJ is generous and should not be spent on a circuit that has no clamp, because a 40 V part in a 48 V transient is a warranty claim rather than an avalanche event.
On supply, the part travels on tape with the date code on the label, the reflow peak is 260 C, and the moisture level follows the packing list. Incoming inspection samples the on resistance at 10 V and 4.5 V, the threshold at 250 microamp, the breakdown at 250 microamp and the diode drop at 20 A, and the exposed pad is checked by x-ray on the first article of each lot.