Contact Us

VBE18R07S

Brand: VBsemi
VBsemi VBE18R07S is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBE18R07S — Discrete & Power Semiconductors | Superb Automation

VBE18R07S

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBE18R07S from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBE18R07S: 800 V at 7 A in a DPAK

The VBE18R07S is a single N channel MOSFET in TO252 rated at 800 V, plus or minus 30 V on the gate, 7 A of drain current, with a threshold of 3.5 V and 770 milliohm at a 10 V gate, on superjunction multi epitaxial silicon.

Eight hundred volts is the top of the DPAK range. It is used where the bus is 600 V or where a 480 V supply has to be switched without a clamp, and where the current is small enough that 770 milliohm does not cook the die.

At 770 milliohm and 2 A the loss is 3 W. At 1 A it is 0.77 W. The part is a 1 to 1.5 A switch in a board, and everything above that needs a heatsink or a larger body.

Key data for the VBE18R07S

ConfigurationSingle N channel
PackageTO252, DPAK, exposed drain tab
VDS800 V
VGSPlus or minus 30 V
Vth3.5 V
ID7 A
RDS(on) at 10 V770 milliohm
TechnologySuperjunction, multi epitaxial
Body diodeIntrinsic, hard recovery
Thermal pathDrain tab, small die, small heat
Gate chargeNot published, modest at this die size
Typical use600 V bus, high voltage start up, capacitor discharge
IsolationNone, the tab is the drain

The last hundred volts of margin

An 800 V part buys 150 V over a 650 V part, and that margin is worth more than the resistance it costs when the bus is 600 V and the leakage spike is 150 V. On a 400 V bus the extra margin is unnecessary and the higher resistance is a straight loss.

There is a second reason to go to 800 V: cosmic ray and terrestrial neutron induced failure. A high voltage die has a failure rate that rises with the applied voltage and with altitude, and derating to 60 or 70 per cent of the rating is a common rule for equipment that runs in the field for years. An 800 V part on a 500 V bus is derated at 62 per cent, which is why some products use a part that looks oversized.

That rule is not in the catalogue page and it is not in most data sheets. It comes from the application note, and it is the reason a 600 V bus sometimes carries an 800 V or 900 V device.

Under one amp in a DPAK

At 770 milliohm and 1 A the loss is 0.77 W, and at 0.5 A it is 0.19 W. Both are comfortable in a DPAK with a copper plane, and the part is thermally easy at the currents it is actually used at.

The difficulty moves to the switching. At 800 V the output capacitance stores energy that is lost at every turn on, and with a small die the energy per cycle is small, so the frequency can be high. A 100 kHz converter with 1 A is entirely reasonable for this part, which is the opposite of the 500 V case where the die is larger and the frequency has to be lower.

The gate drive is the same as the rest of the family: 10 V nominal, a turn off resistor to control the dV/dt, and a clamp on the drain to keep the spike inside the rating.

The gate drive for an 800 V part deserves a note of its own. The gate sits at source potential, which in a high side position moves with the bus, so a transformer isolated drive or an opto isolated driver is usual. Those drivers have a propagation delay in the hundreds of nanoseconds, and at 100 kHz that delay is a meaningful fraction of the period. The turn off has to be fast enough that the drain current reaches zero before the voltage rises, or the overlap loss climbs. A 800 V, 770 milliohm die switches a small current, so the overlap loss is small, but the dV/dt at turn off is high and the driver has to hold the gate firmly down through it. A gate resistor to source at the driver secondary is not optional here.

Series connection of two 800 V parts is sometimes proposed to reach 1200 V, and it works only with a voltage balancing network across each device. Without it, the leakage currents and the capacitance dividers decide which die takes more than its share, and the one that takes more fails first. The balancing resistors have to carry several times the worst case leakage, which at 800 V is a continuous loss, and that loss usually makes the series connection worse than a single higher voltage part.

Where the part fits and where it does not

It fits a 600 V bus start up circuit, a high voltage bleeder or discharge path, an offline flyback at very low power, and any place where 650 V leaves too little margin. It does not fit a PFC above 100 W, and it does not fit a bridge or a synchronous rectifier.

Our incoming inspection plan page covers what is checked when a high voltage part arrives, because a 800 V die that fails at 600 V is a batch problem and not a circuit problem.

The sourcing side of this part is covered on the supplier quality audit. For a 800 V die that has to hold its rating, that page covers what is checked at the source before the reel is released.

Questions we get on this code

Can it switch 7 A? Only with a heatsink and only for a pulse. At 7 A the conduction loss is 38 W. Plan for 1 A in a board.

Is 800 V enough for a 600 V bus? Yes with a clamp. Without one, a leakage spike plus a bus transient can exceed the rating.

Does the high resistance matter in a start up circuit? Not much, because the current is small and the part is on for a short time. It matters in a converter running continuously.

What should a purchase order carry? Part number, TO252, reel size and date code. We confirm what is available when the quantity is known.