Contact Us

VBE16R15S

Brand: VBsemi
VBsemi VBE16R15S is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBE16R15S — Discrete & Power Semiconductors | Superb Automation

VBE16R15S

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBE16R15S from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBE16R15S: a 600 V super junction switch offered in three bodies

The VBE16R15S is the TO-252 member of a family that the vendor also lists as VBM16R15S and VBMB16R15S, in the TO-220AB and the TO-220 full pack. All three share one die: 600 V from drain to source, plus or minus 30 V on the gate, 0.28 ohm maximum on resistance at a 10 V gate with 8 A flowing, 15 A of continuous drain current with the case at 25 C and 9.4 A with the case at 100 C. Gate charge is 43 nC maximum at the summary level and 48 nC typical in the electrical table, which is the kind of split that a buyer has to read twice before quoting a driver.

Having three bodies on one die is genuinely useful. A 600 V part that starts in a TO-220 for a prototype and moves to a TO-252 for production keeps the same electrical rows, the same gate charge and the same avalanche behaviour, and the only thing that changes is the thermal path. The reverse is also true: a product that outgrows the TO-252 pad can move to the full pack without requalifying the switching behaviour. The three order codes have to be kept apart on the purchase order, because the packing, the moisture level and the dissipation all differ.

The ratings a buyer checks first

Drain to source voltage600 V
Gate to source voltageplus or minus 30 V
On resistance at 10 V gate, 8 A, 25 C0.28 ohm maximum
Continuous drain current, case at 25 C15 A
Continuous drain current, case at 100 C9.4 A
Pulsed drain current45 A
Single pulse avalanche energy9 mJ from 50 V into 28.2 mH, 4.5 A peak
Power dissipation156 W in the TO-220 body, 34 W in the TO-252
Linear derating factor3.6 W per C
Junction to case, junction to ambient0.8 and 60 C per watt
Gate threshold voltage2 V minimum, 4 V maximum
Total gate charge at 10 V gate and 520 V drain48 nC typical, 96 nC maximum
Input, output and reverse transfer capacitance800, 70 and 8 pF
Turn on delay and rise time13 and 11 ns typical
Turn off delay and fall time81 and 25 ns typical
Body diode forward voltage at 8 A1.5 V maximum
Reverse recovery time and charge345 ns and 4.5 microcoulomb typical
Junction and storage rangeminus 55 to plus 150 C

Reading the electrical table instead of the front page

The resistance row says maximum, not typical, and that changes the arithmetic. The summary page prints 0.28 ohm as a maximum at 25 C, while the electrical table repeats 0.28 in the typical column with no maximum beside it, which is a printing inconsistency a buyer should notice rather than average away. Planning with 0.28 ohm at 25 C is the safe reading; the same die at 125 C is nearer 0.48 ohm, and 6 A through 0.48 ohm is 17 W, which no TO-252 pad will hold for long.

The avalanche row is the surprise on this part. Where the 650 V member quotes 350 mJ, this one quotes 9 mJ from a 50 V rail into 28.2 mH at 4.5 A. That is a much smaller energy and it is not a typographical error: the same family number in a different die revision carries a different avalanche capability, and a clamp that was adequate on the 650 V part will not necessarily protect this one. A buyer who treats the two parts as interchangeable because they share a voltage class and a body is one transformer away from a failure.

The switching rows are slow at the top end. Turn off delay is 81 ns typical and 90 ns maximum with a 9.1 ohm gate resistor, against 61 ns typical on the 650 V member, so the two parts are not the same die despite the shared gate charge. Gate charge is 48 nC typical and 96 nC maximum, which is a two to one spread: a driver sized on the typical number will be marginal on a hot lot, and the 96 nC figure belongs in the driver calculation. The input capacitance is only 800 pF, so most of that charge is gate drain charge, 21 nC of it, which is the number that decides the Miller plateau and the turn on dV/dt.

The body diode is slow, at 345 ns of reverse recovery against 45 ns on the 650 V member. In a bridge that is the difference between a hard switched leg and a leg that needs a small dead time and a snubber, and 345 ns at 100 kHz is 3.5 per cent of the period spent recovering. On a discontinuous flyback the diode never sees a forced reverse recovery and the row does not matter, which is a large part of why this part is priced and used the way it is.

Where a 600 V super junction device earns its place

The main case is an offline flyback or a forward converter at 50 W to 150 W, where 600 V covers a 380 V bus with the usual overshoot and the 45 A pulse covers the start up inrush. The second case is a power factor correction stage in a lighting driver or an adapter, where the 800 pF input capacitance and the 96 nC worst case gate charge let a small controller drive the part directly at 65 kHz. The third is a relay replacement in a mains switching board, where the 15 A case rated current and the 34 W TO-252 dissipation are enough for a few amps of continuous load with a proper pad.

It is a poor fit for a bridge at high frequency. The 345 ns diode, the 4.1 V per nanosecond reverse dV/dt limit and the low avalanche energy of 9 mJ all point away from hard commutation. A buyer who needs a 600 V bridge leg at 100 kHz should look at the part's diode rows first and the resistance row second, and should expect to pay for a faster diode.

Sourcing notes and the second source question

Because three order codes share this die, the second source question starts with the body rather than with the electrical data. A TO-220AB, a TO-220 full pack and a TO-252 carry three different junction to ambient paths, and the 156 W and 34 W dissipation rows on the same sheet make that plain. Our pin to pin cross reference lists the body and the thermal resistance beside the voltage and the resistance, so a substitute is compared on the package it will actually be soldered into.

Where a second vendor's 600 V part is being considered, how to verify a drop in replacement covers the four tests that catch the usual failures here: avalanche with the real transformer leakage, diode recovery at the real load current, threshold at the cold corner and the tab temperature on the customer's own pad. The avalanche test is the one most often skipped and the one that separates two parts that look identical on paper.

Questions we answer before a reel is booked

The first question is which body the price is for. The three codes are not interchangeable in packing or in thermal performance, and a quotation that names only the family will be read as the cheapest body until the purchase order says otherwise. The second is the gate charge to use in the driver calculation: 48 nC typical is the switching number and 96 nC maximum is the number a worst case calculation needs, and a driver that only meets the typical figure will run hot on some lots.

The third question is the avalanche energy. Nine millijoules is small, so the clamp has to be checked against the actual leakage inductance rather than against a rule of thumb carried over from another part. The fourth is the diode. At 345 ns of recovery this is not a bridge part, and a buyer who needs one should be told so before a reel is booked.

On supply, the TO-252 tape follows the standard outline, the reflow peak is 300 C for 10 seconds at 1.6 mm from the case, and the date code and moisture level travel on the label and the packing list. Incoming inspection samples the on resistance at a 10 V gate, the threshold at 250 microamp, the breakdown at 250 microamp and the gate leakage at 20 V, and the avalanche row is verified on a sample basis rather than on every lot.