Contact Us

TMP6131DYAR

Brand: Texas Instruments
Texas Instruments TMP6131DYAR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TMP6131DYAR — Power Management & Signal Chain | Superb Automation

TMP6131DYAR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TMP6131DYAR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TMP6131DYAR ten kilohm silicon linear thermistor with a positive temperature coefficient

The TMP6131DYAR is a silicon thermistor, not a ceramic one. It presents ten kilohms at twenty five degrees with one percent tolerance, and its resistance rises with temperature on a curve that is close enough to a straight line that a two point calibration and a polynomial are all the conversion needs. The temperature coefficient is 6400 parts per million per degree at twenty five degrees, and the tolerance on that coefficient is 0.2 percent typical across the range, which is the number that separates this device from an NTC thermistor with a wide spread and a steep curve.

The positive coefficient is a safety property as well as an electrical one. In an NTC the resistance falls as temperature rises, so a short to the supply produces more current, more heat and less resistance in a loop that runs away. In this device a short to the supply raises the resistance and limits the current by itself, which the document describes as a built in fail safe. The part is specified from minus 40 to plus 150 C, has a thermal response time of 0.6 seconds in the smallest body, and drifts about half a percent after a thousand hours at 150 C in the 0603 body.

Key parameters taken from the TMP6131DYAR document

Typesilicon thermistor with a positive temperature coefficient, linear resistance change
Nominal resistance10 kilohms at 25 C, 9.9 to 10.1 kilohms, plus or minus 1 percent
Tolerance over rangeplus or minus 1 percent from 0 to 70 C, plus or minus 1.5 percent from minus 40 to 150 C
Temperature coefficient6400 ppm per degree at 25 C, 5910 at 85 C, 6220 at minus 35 C
Coefficient tolerance0.2 percent typical at 25 C, 0.3 percent at 85 C, 0.4 percent at minus 35 C
Operating rangeminus 40 to plus 150 C
Response time0.6 s in the smallest body, stirred liquid measurement
Long term drift0.5 percent typical over 1000 hours at 150 C in the 0603 body, 1.2 percent maximum
Biaskeep the top resistor of the divider at 10 kilohms and respect the bias limit, the resistance curve depends on it
Failure behaviourresistance rises on a short to the supply, limiting self heating
PackageSOT-5X3 body DYA, 1.60 by 0.80 mm, also 0402 X1SON and a two pin through hole body
Order code factsTMP6131DYAR, SOT-5X3 DYA 2 pins, 3000 pieces on a large reel, minus 40 to plus 150 C, marking 1GK, Active; the lead finish column prints a call to the vendor on the plain row

The table above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for the first article.

Where the numbers matter in a real build

The conversion is arithmetic, not a lookup table. Because the curve is close to linear, a product can compute temperature from the divider voltage with a polynomial and no calibration table in memory, which on a small controller is worth more than the part cost. The document provides the resistance to temperature table and the polynomial method, and the condition attached to both is that the top resistor stays at ten kilohms and the bias stays inside the printed range. Changing the top resistor to save a part changes the curve and voids the conversion.

Self heating is the error that a first article never shows, because it only appears at the temperature where the resistance is lowest and the current is highest. At the cold end the resistance falls and the current through the divider rises, so the device heats itself and reads high. The smallest body has a thermal mass measured in fractions of a joule per degree, so a bias of a few volts is enough to move the reading by a degree. The document prints the thermal resistance and the self heating formula, and the first article should measure the reading at two bias levels to see the effect directly.

The tolerance over temperature is what a production line cares about. One percent at twenty five degrees sounds better than it is, because the interesting range for most products is either cold or hot, and the tolerance there is one and a half percent. That is still an order of magnitude better than a typical NTC, whose tolerance curve has to be carried as a table with a calibration step per unit. The trade is that this device cannot be replaced by a ten kilohm NTC on the same footprint without rewriting the conversion, because the curve direction is opposite.

The order row is worth reading before a purchase order. The plain TMP6131DYAR row carries RoHS compliance and a call to the vendor in the lead finish column, while the A row of the same string is printed as obsolete with a tin finish and a level 3 moisture class. For a product that needs a declared finish, the safe step is to ask for the finish on the order and to confirm the label, rather than to assume that the plain row and the A row describe the same shipment.

  • Resistance measured at three temperatures on the real board, against the printed table, with the divider bias the product uses.
  • Self heating checked by reading the same temperature at two bias levels and comparing the two results.
  • Divider ratio with the actual one percent top resistor, since the curve assumes a ten kilohm partner.
  • Response to a step in air temperature, which depends on the copper and the airflow around the body.
  • Drift after a burn in at the top of the range, if the product has a long life requirement at temperature.
  • Lead finish and moisture class confirmed on the carton label against the order.

Which projects this part fits

This thermistor is used where an NTC would need linearisation or calibration: motor control and charger thermal derating, battery pack temperature sensing, LED driver protection, HVAC and thermostat products, industrial control and appliances, building automation, display backlight compensation and any board that has to report a temperature to a processor without a conversion table. Its linearity is the reason it appears in products that moved away from NTC parts after a calibration step proved too expensive in volume.

Questions that come up before a purchase order is released

Can this replace a ten kilohm NTC directly?

Not without a software change. The nominal resistance at twenty five degrees matches, and the curve goes the other way, so the same divider produces falling voltage with rising temperature instead of rising voltage. The conversion code and the fault thresholds have to be reversed, and the protection logic has to be checked, because a shorted sensor now reads as a high temperature rather than a low one.

Why does the bias voltage matter?

Because the resistance depends on the current through the device, and the printed resistance to temperature table assumes a specific bias and a ten kilohm top resistor. Running the divider at a higher voltage raises the self heating and shifts the reading, and running it lower reduces the resolution at the converter. The document prints the recommended operating point.

Is 150 C really usable?

The device is specified to 150 C and the drift figures are given at that temperature. The usable limit in a product is set by the board, the solder and the drift budget, not by the device alone. A product that needs half a percent of accuracy after a thousand hours has to derate, because the maximum drift at 150 C is printed at 1.2 percent in the 0603 body.

What is the difference between the DYA and DEC bodies?

Size and response time. The DYA is a 0603 body and the DEC is an 0402 body, and the smaller body responds faster and heats less for the same bias, at the cost of placement difficulty and a smaller thermal pad. The through hole body exists for products that still use a leaded assembly, and its drift figures are printed separately.

Does the part need a filter capacitor?

It needs whatever the converter input needs, and the capacitor sitting across the divider also sets the response to a fast temperature step. The device itself is resistive and has no supply pin, so there is nothing to decouple. A capacitor of a few nanofarads at the converter input is a common choice and it should be placed at the converter, not at the thermistor.

How SUPERB handles this line

We supply the TMP6131DYAR on the original 3000 piece reel with date code and lot traceability, and we confirm the lead finish on the label because the same string appears with more than one finish row in the document. For customers moving a product from an NTC to a silicon thermistor we quote the top resistor of the divider on the same order, since the pair decides the curve. The sensor selection guide page covers the neighbouring sensing parts, and the medical device components page covers the case where the drift budget has to be documented for a regulated product.