TMP451AQDQFRQ1
Product Specifications
TMP451AQDQFRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The TMP451AQDQFRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TMP451AQDQFRQ1 automotive remote and local temperature sensor in the two millimetre WSON
The TMP451AQDQFRQ1 is the automotive grade member of the TMP451 family in the DQF body, a two by two millimetre WSON, with one local sensor on the die and one remote channel that reads a diode connected transistor inside a processor, an FPGA or a discrete device. It is qualified to AEC-Q100 grade 1 over minus 40 to plus 125 degrees ambient, which is the qualification most automotive sub systems need.
The part carries a one degree maximum accuracy on both the local and the remote channel, 0.0625 degree resolution on both, a 1.7 to 3.6 volt supply and logic range, 27 microamps of operating current and 3 microamps in shutdown. The features that matter in a real product are the ones around the measurement: series resistance cancellation, programmable non-ideality factor and offset correction, a programmable digital filter, and diode fault detection, all of which exist because a remote diode in a hot processor is a difficult thing to measure accurately.
Key parameters taken from the TMP451AQDQFRQ1 document
| Channels | One local sensor, one remote diode channel |
| Accuracy | Plus or minus 1 C maximum on both local and remote, over the typical operating range |
| Resolution | 12 bit, 0.0625 C per code, on both channels |
| Supply | 1.7 to 3.6 V for the supply and for the logic interface |
| Current | 27 microamps operating, 3 microamps in shutdown |
| Qualification | AEC-Q100 grade 1, minus 40 to plus 125 C ambient |
| Remote features | Series resistance cancellation, programmable non-ideality factor, programmable offset |
| Filter | Programmable digital filter to trade update rate for noise |
| Diagnostics | Diode fault detection on the remote channel |
| Interface | Two wire and SMBus, with the standard command set |
| Package | WSON, DQF, 2.00 by 2.00 mm; the DQW wettable flank body of the same family is 2.50 by 2.50 mm |
| Thermal | Junction to ambient around 128 to 171 degrees per watt depending on the body, junction limit 150 C |
| Order code facts | TMP451AQDQFRQ1, DQF eight pin WSON, tape and reel, automotive grade 1 |
| Body choice | The wettable flank DQW body exists so an automated visual inspection can confirm the solder joint on automotive lines |
The table above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for the first article.
Where the numbers matter in a real build
The wettable flank option is not cosmetic on an automotive line. A two millimetre WSON has its joints under the body, and an automated visual inspection cannot see them, so the package either gets x ray on every board or gets a wettable flank that shows a fillet at the side. The DQF body printed for this code is the plain version, and a program that requires visual inspection acceptance should compare it against the DQW body of the same family before freezing the footprint, because the two are not the same land pattern.
Series resistance cancellation and the non-ideality factor are the two registers that decide whether the remote channel is usable at all. On an automotive board the remote diode is often several centimetres away, through a connector, next to a switching node, and the factor published by the processor vendor is a starting point rather than a measurement. The practical flow is to set the factor from the vendor document, run a three point comparison against a reference at 25, 85 and 125 degrees, and store the residual offset in the same place the production image keeps its calibration data.
The digital filter is the answer to noise on a switching board, and it costs update rate. A filtered reading that lags the die by a second is fine for a fan curve and useless for a protection loop that has to act in tens of milliseconds. On an ECU with a fast transient load the honest board has two paths: the filtered channel for the control law and the unfiltered alert threshold for the protection, and the difference between the two readings at a load step is the diagnostic that tells the firmware the filter is masking something.
The supply range of 1.7 to 3.6 volts means this part can sit on the same rail as the processor it is watching, which removes the level shift question but puts the sensor on the noisiest rail on the board. The document prints the supply rejection and the decoupling requirement; in practice the board rules is a capacitor at the package with a via to the ground plane beside it, and no long shared trace back to the regulator.
- Remote channel against a reference at 25, 85 and 125 degrees, with the non-ideality factor from the monitored device document.
- Series resistance limit with the real harness length and connector in place, not on a bench lead.
- Filter settling time at the setting the control firmware uses, measured from a step change in die temperature.
- Diode fault flag behaviour when the remote connection opens and when it shorts.
- Alert and shutdown path timing from the crossing of the limit to the pin, on the production firmware.
- Body and land pattern review against the visual inspection requirement of the customer's line.
Which projects this part fits
This part fits automotive infotainment and instrument cluster thermal management, ECU, transmission control and body control processor monitoring, ADAS compute module thermal protection, and any automotive board where the processor's own thermal diode is the accessible temperature point. For SUPERB customers building automotive electronics and ADAS hardware it is the part that turns an existing diode into a calibrated reading without adding a package next to the processor.
Questions that come up before a purchase order is released
What is the difference between the DQF and DQW bodies?
The DQF is the plain two by two millimetre WSON printed for this code and the DQW is the wettable flank version at two and a half millimetres square. The land patterns differ, so a board built for one does not accept the other. The choice is driven by whether the customer's inspection plan requires a visible fillet on every joint.
How accurate is the remote channel in practice?
The document prints one degree maximum, and that figure assumes the non-ideality factor and the series resistance are set for the actual diode and routing. Left at the defaults, the error at high temperature is typically larger than one degree and grows with temperature, which is why the first article comparison against a reference is not optional.
Why is the operating current so low?
Because the part can stay powered in a module that sleeps. Twenty seven microamps is small enough that the sensor can remain on the always on rail and be read before the processor is fully awake, so the thermal state is known at boot rather than a second later.
Does the part need a separate analogue rail?
No, the supply and the logic interface share the 1.7 to 3.6 volt range, so it can sit on a processor IO rail. The consequence is that the decoupling has to be local and the ground return short, because the same rail carries the switching current of the processor.
What does the automotive suffix change for a purchasing team?
The qualification row and the change control. The string ships on tape and reel with the grade 1 marking, and the customer's approved vendor list usually names the exact order code. Substituting the catalog row of the same family is a qualification question, not a price question, and it should be raised before a purchase order rather than after.
How SUPERB handles this line
We supply the TMP451AQDQFRQ1 on original tape and reel with the automotive grade verified on the label, and we handle the moisture and ESD requirements of a two millimetre WSON as standard. Where the board is choosing between remote sensor families, the power management cross reference page lists them by channel count and package. Where the question is keeping an automotive part number stable across a program, component obsolescence management covers the options, and incoming inspection plan covers what to verify on arrival.