Contact Us

VBA1108S

Brand: VBsemi
VBsemi VBA1108S is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBA1108S — Discrete & Power Semiconductors | Superb Automation

VBA1108S

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBA1108S from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBA1108S: a 100 V part with only a 10 V gate column

The VBA1108S is a single N channel MOSFET in an SOP8 body, 100 V drain to source, a plus or minus 20 V gate window, a threshold of 2.5 V, a drain current of 15.5 A, and an on resistance of 8 milliohm at a 10 V gate.

The catalogue page publishes one resistance column, at 10 V, and no column at 4.5 V. On a part with a 2.5 V threshold that is an important omission rather than a detail: it means the right gate drive for this part is 10 V, and a 5 V drive is outside what the vendor was willing to publish.

Eight milliohm at 100 V is the lowest resistance in this band, so the part is the power member of the family: the one to use when the current is 10 A and the drive is 10 V.

Key data for the VBA1108S

ConfigurationSingle N channel
PackageSOP8, surface mount, eight leads
VDS100 V
VGSPlus or minus 20 V
Vth2.5 V
ID15.5 A
RDS(on) at 10 V8 milliohm
RDS(on) at 4.5 VNot published, and with a 2.5 V threshold it should not be assumed close to the 10 V figure
TechnologyTrench
Gate chargeNot published on the catalogue page, expect a large figure at this die size
Thermal limitAbout 1.5 W with the leads on copper, more with a plane
Body diodeIntrinsic, anode at source

Fifteen and a half amps at 8 milliohm

At 15.5 A and 8 milliohm the loss is 1.9 W, which an SOP8 with all eight leads on a plane can pass in still air at a 100 C rise if the copper is generous. That is a better match between rating and package than most parts in this band, and it suggests the vendor set the current from a thermal calculation rather than from the die.

In a warm enclosure the working current is 10 to 12 A. At 12 A the loss is 1.15 W and the junction rise is about 65 C on a good pad, which is a sensible working point. At 15 A it is 1.8 W and the margin is thin.

The gate charge matters as much as the resistance at this die size. A 8 milliohm 100 V die has an input capacitance in the low nanofarads, and a driver has to source and sink an amp to switch it in 50 nanoseconds. A weak driver turns the switching edge into a linear event, which is how a low resistance part ends up hotter than a higher resistance part driven properly.

Working around a single gate column

The absence of a 4.5 V column is a signal, and the practical rule is simple: drive this part at 10 V or do not use it. A 12 V rail through a resistor to the gate gives about 11 V after the driver drop, which is inside the 20 V window and lands on the published column.

In a synchronous buck this is normal, because the bootstrap capacitor sits at the rail plus 10 V and drives the high side gate to a proper level. In a 48 V non isolated converter the same arrangement works. In a circuit with only a 5 V supply it does not, and the 27 milliohm logic level part in the same family is the right choice instead.

The 2.5 V threshold also has a switching consequence: the part needs 2.5 V of gate before it conducts at all, so a slow gate drive spends longer in the linear region, and the crossover loss rises. A gate resistor of 4.7 to 10 ohm rather than 22 is appropriate here, and the driver has to be able to feed it.

The power member of the family, and when to pick it

Pick it when the drive is 10 V, the current is 8 to 12 A, and the rail is 48 V or a 60 V battery. Pick a smaller die when the frequency is high or the current is low, because the gate charge of this part is a real loss at 300 kHz and above.

For the whole family the body is the same, so a board can be built with one member and changed to another late, which is useful when the current budget is not final. Our supplier scorecard page covers how a source is scored across a programme, and a four member family in one body is a case where a scorecard on the family is more useful than one on a single code.

The sourcing side of this part is covered on the supplier corrective action. For a power die whose failure mode is thermal rather than electrical, that page covers how a non conformance is closed out.

Questions we get on this code

Can it be driven at 5 V? It will conduct, but no resistance is published at 5 V and the loss will be substantially higher than the 8 milliohm figure. Do not build a thermal calculation on it.

Is 15.5 A real? With a plane and some airflow at 25 C ambient, close. In a closed box plan on 10 to 12 A.

Does it need a snubber? At 100 V and 10 A with a fast edge, yes, a resistor capacitor snubber across the low side device controls the ringing, and the loop area has to be small.

What is the packing? SOP8 normally ships on 2500 or 3000 piece reels. We confirm the size when quoting.