VB3222A
Product Specifications
VB3222A
VBsemi — Discrete & Power Semiconductors
Product Overview
The VB3222A from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VB3222A: the same dual with twenty volts of gate window
The VB3222A is a dual N channel MOSFET in a SOT23 six lead body, 20 V drain to source, a plus or minus 20 V gate window, a threshold between 0.5 and 1.5 V, a 6 A current figure, and an on resistance of 26 milliohm at a 4.5 V gate and 22 milliohm at 10 V.
Against the base part in the same family the change is the gate window, which goes from 12 to 20 V, and the low gate column, which moves from 2.5 to 4.5 V. The resistance at the working point is 26 milliohm rather than 22, so the wider window costs a little conduction in exchange for a gate that can be driven from a 12 V rail without a clamp.
That trade is worth making in any 12 V circuit. It is worth avoiding in a 3.3 V circuit, where the 2.5 V column of the base part is the more useful number.
Key data for the VB3222A
| Configuration | Dual N channel, independent |
| Package | SOT23, six leads, surface mount |
| VDS | 20 V |
| VGS | Plus or minus 20 V |
| Vth | 0.5 to 1.5 V |
| ID | 6 A |
| RDS(on) at 4.5 V | 26 milliohm |
| RDS(on) at 10 V | 22 milliohm |
| Technology | Trench |
| Gate charge | Not published on the catalogue page |
| Thermal limit | About 400 to 500 milliwatt in total for the body |
| What changed from the base part | Gate window 12 to 20 V, low gate column 2.5 to 4.5 V, resistance at the working point 22 to 26 milliohm |
Twelve volts of rail and twenty of window
A 12 V rail switched by an N channel needs the gate above the source by 4 to 10 V, which a bootstrap or a charge pump provides. With a 12 V window the gate sits near the rail plus the drive and the margin to the limit is thin. With a 20 V window the same circuit has 8 V of headroom and a supply transient does not reach the oxide.
That is the whole justification for the A suffix. It is not a better die, it is a die screened or built for a wider gate, and in a 12 V or 15 V circuit that is the parameter that fails first in the field.
There is a cost beyond the resistance. A wider gate window usually means a thicker gate oxide, which means a slightly higher gate charge for the same channel area. Since the gate charge is not published here, a circuit at 200 kHz or above should ask for it, because a part that is 4 milliohm worse and 2 nanocoulombs heavier is a double penalty on a fast switching node.
The two channel sum at 12 V
At 12 V in and 2 A per channel the pair dissipates 208 milliwatt at 26 milliohm, which is comfortable. At 3 A per channel it is 468 milliwatt, which is at the practical limit of the body on a good pad. Above that the copper has to grow or the current has to come down.
The gate drive in a 12 V circuit normally comes from a controller with a 5 V or 12 V driver. A 5 V drive puts the resistance between the 4.5 and the 10 V columns, near 27 milliohm by interpolation, so the 26 milliohm figure is a fair working value for a 5 V driver and a slightly pessimistic one for a 10 V driver.
Body diode conduction is the third term. In a synchronous arrangement the dead time forces the diode to conduct, and at 0.8 V forward and 2 A for 50 nanoseconds at 200 kHz the loss is 16 milliwatt per channel, small but not zero. Short dead time and a fast body diode both help, and neither is on the catalogue page.
Choosing between the two members of the family
Pick the base part when the gate is driven below 5 V and the circuit is a battery powered product where the 2.5 V column matters. Pick the A when the gate is driven from a rail that can reach 10 or 12 V and the board has to survive a supply transient.
The two parts are pin compatible in the same body, which means a board can carry one footprint and two order codes, and that is the practical way to hold a second source and a supply option at the same time. Our safety stock planning page covers how a buffer is sized against a build plan, and a footprint that accepts two codes is the cheapest buffer there is.
The sourcing side of this part is covered on the strategic sourcing. For a family that offers two gate windows in one footprint, that page covers how the supply is held for the life of the product.
Questions we get on this code
Is the A a drop in for the base part? In the same footprint, yes. The difference is the gate window and 4 milliohm, both of which are safe in the direction of the A. Going the other way is not safe.
Can it be used at 15 V drain? The rating is 20 V, so 15 V nominal is 25 per cent of margin, which a switching node will eat. Use it on 12 V and below.
What about the gate at 12 V with no clamp? That is the point of the A. Check the driver's absolute maximum as well, because a driver that clamps at 13 V is not protecting a 20 V gate.
Does it ship on a small reel? Six lead SOT23 normally ships at 3000 pieces, with a smaller option for prototypes. We confirm the reel on the offer.