MAX9141EKA+T
Product Specifications
MAX9141EKA+T
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The MAX9141EKA+T from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
MAX9141EKA+T: 40 ns at 10 mV of Overdrive, With a Latch That Can Freeze the Output
The MAX9141EKA+T is the single channel member of the MAX9140, MAX9141, MAX9142 and MAX9144 comparator family from Analog Devices, in the 8-pin SOT23 package on tape and reel. It runs from 2.7 V and up, switches in 40 ns at 10 mV of overdrive, draws 150 uA per comparator at 3 V, has 500 uV of offset, accepts inputs that extend beyond both supply rails, and drives its output to within 300 mV of either rail without a pull-up. This is the one part number in the family that carries both the latch enable input and the shutdown function, and the data sheet presents the family as a faster, lower power and lower cost upgrade to the MAX941, MAX942 and MAX944.
Forty nanoseconds at 10 mV and eighty nanoseconds at 5 mV are different tests
The MAX942 quotes 80 ns at 5 mV of overdrive; the MAX9141 quotes 40 ns at 10 mV. Doubling the overdrive while halving the delay is a strong result, but it is not a factor of two at equal drive, and a buyer comparing the two headline numbers should expect less improvement at 5 mV than the arithmetic suggests. What the 40 ns does establish is the ceiling: one edge every 40 ns is a 12.5 MHz square wave, so the part is a fast threshold detector and not a pulse shaper for a 100 MHz logic signal.
Five hundred microvolts of offset against a 10 mV overdrive is five percent of the drive, which is four times better than the 1 mV against 5 mV of the older part. On a signal that swings tens of millivolts, the offset is no longer the dominant term and the delay figure becomes the real specification.
The latch enable turns a comparator into a sampling element
With the latch input asserted, the output holds the state it had when the latch was taken, regardless of what the inputs do afterwards. That is what makes the part usable at the front of an analogue to digital converter, where the comparator decision has to be frozen while the converter quantises it, and it is also what removes the chatter problem on a noisy input during the sampling window. The aperture is set by the latch timing rather than by the comparator delay, so a system that needs a defined sampling instant can get one without an external sample and hold.
Shutdown leakage, and where the maximum hides
The pin table gives a shutdown output leakage current of 0.04 uA typical and 1 uA maximum with SHDN held low, so the maximum is twenty five times the typical. A build that budgets the typical value on a multi channel assembly with a shared shutdown line can be an order of magnitude out once the parts are at the limit. The supply current itself is 150 uA per comparator at 3 V, which is 0.45 mW, and the shutdown state is what makes this part practical in a battery product where the detector only runs for part of the duty cycle.
| Parameter | Published value | What it decides |
|---|---|---|
| Propagation delay | 40 ns at 10 mV overdrive | 12.5 MHz of square wave at best |
| Offset voltage | 500 uV | Five percent of the specified overdrive |
| Supply current | 150 uA per comparator at 3 V | 0.45 mW standing, plus a shutdown path |
| Shutdown leakage | 0.04 uA typical, 1 uA maximum | The maximum is 25 times the typical |
| Input range | Extends beyond both supply rails | No inversion when a signal crosses a rail |
| Output swing | Within 300 mV of either rail | Direct drive into CMOS or TTL |
| Latch and shutdown | Both on the MAX9141 only | Frozen output for a sampling aperture |
| Supply range | 2.7 V and up | 3 V and 5 V systems from one part number |
Questions buyers ask before they order this part number
Is the latch input a logic input or a differential pair? It is a single-ended logic input referenced to ground, so it can be driven from the same logic family as the rest of the board. The requirement is that it reaches a valid logic level at the moment the sampling instant has to occur, and that the driving edge is not routed next to the analogue input, where the coupling shows up as a step at the comparator input exactly when the decision is being taken.
What happens to the output when shutdown is asserted? The comparator stops switching and the output goes to a defined state rather than floating, and the leakage specification describes what the pin does in that condition. A board that uses shutdown to multiplex two comparators onto one line should confirm the state the downstream logic needs during the off phase, because a defined state is not the same as a high impedance state.
The part is listed in the analog and mixed-signal IC category. Buyers comparing high speed comparator families open amplifier cross reference, and projects re-costing a detector stage use how to reduce component cost.
Request Quote — In Stock, 100% New & Original, Full Warranty