Contact Us

OP275GSZ

Brand: Analog Devices
Analog Devices OP275GSZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

OP275GSZ — Analog & Mixed-Signal ICs | Superb Automation

OP275GSZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The OP275GSZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

OP275GSZ: a dual audio amplifier with 6 nV per root Hz and 22 V per microsecond

The OP275GSZ is a dual operational amplifier built on the Butler front end, which puts a bipolar input stage next to a JFET stage so the part keeps bipolar accuracy and noise with JFET speed and input current. The published numbers are 6 nV per root Hz of voltage noise, 22 V per microsecond of slew rate, 9 MHz of bandwidth, 1 mV of maximum offset and 5 mA of supply current for both channels. It drives a 600 ohm load to 10 V rms while holding distortion at 0.0006 percent.

Published values

ParameterValue
ChannelsTwo
Voltage noise6 nV per root Hz
Slew rate22 V per microsecond
Bandwidth9 MHz
Total harmonic distortion plus noise0.0006%
Maximum offset voltage1 mV
Offset current2 nA
Supply current5 mA for both channels
Output drive600 ohm to 10 V rms
Packages8-lead SOIC, 8-lead PDIP

Why a hybrid input stage matters in audio

A pure bipolar input stage has low voltage noise and a bias current that rises with temperature and source resistance. A pure JFET stage has almost no bias current and a higher voltage noise. Putting the two together keeps 6 nV per root Hz and gets the offset current down to 2 nA, which means the part can be used with a high value volume potentiometer or a high impedance filter network without a DC offset appearing as a click when the wiper moves.

The 1 mV maximum offset also removes the output coupling capacitor in many circuits, because 1 mV across a 10 kohm load is 100 nA and the following stage can usually absorb it. A part with 10 mV of offset would need that capacitor back, which then sets the low frequency corner of the whole channel.

Slew rate and the 600 ohm load

22 V per microsecond into a 600 ohm load at 10 V rms output is the condition where the part is specified, and it is a realistic condition for a line driver or a headphone amplifier. Driving a lower impedance load raises the distortion and eventually the output stage current limit becomes the limit rather than the slew rate.

Where to be careful with a substitute

Audio amplifiers are often substituted on noise figure alone. The three parameters that change the sound of a working circuit are the input bias current behaviour with a high source impedance, the output stage capability into the actual load, and the distortion at the output level the circuit runs at, which is not the level in the headline specification.

Where a customer needs a second position on this part, the amplifier cross reference is the starting point, component lead time solutions sets out the checks a substitution has to pass, and one stop BOM sourcing is the short lead time route we quote against.

Two questions buyers ask

Is the OP275 unity gain stable? Yes, it is stable at unity gain and does not need external compensation. Circuits that run at high gain may still need a feedback capacitor for bandwidth limiting.

Can it replace an NE5532 in an existing board? The pinout matches, but the supply current, the input bias current and the output swing differ. The circuit has to be checked for offset and for headroom before the swap is accepted.