Contact Us

LTM8026IV#PBF

Brand: Analog Devices
Analog Devices LTM8026IV#PBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LTM8026IV#PBF — Analog & Mixed-Signal ICs | Superb Automation

LTM8026IV#PBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LTM8026IV#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LTM8026IV#PBF: a 24 V rail from a 36 V bus, and the frequency it can hold

The LTM8026IV#PBF is the I grade of the 36 V, 5 A constant-current module in the 11.25 mm by 15 mm by 2.82 mm land grid array with Au pads and MSL 3. Input range is 6 V to 36 V, output range is 1.2 V to 24 V, and the current loop can be set by a voltage, a resistor or a thermistor. The 24 V output is the row that most applications here care about, because a 24 V rail from a 36 V bus is a 67 percent duty cycle and the module is running near the top of its range.

Published values

ParameterValue
Input voltage6 V to 36 V
Output voltage1.2 V to 24 V, RADJ = 499 ohm for 24 V
Output current5 A, current regulated
Duty cycle at 24 V from 36 V67 percent
Recommended frequency at 24 V200 kHz, RT 210 k
Maximum frequency at 24 V250 kHz, RT 169 k
Off time at 250 kHz1.33 us of a 4 us period
Junction to ambient18.6 C/W
Package11.25 mm x 15 mm x 2.82 mm LGA, Au pads, MSL 3
Temperature range-40 C to 125 C, I grade

A 67 percent duty cycle is an off-time problem

At 36 V in and 24 V out the high side switch is on for two thirds of the period, which leaves 1.33 us of off time at 250 kHz for the low side to conduct and for the bootstrap to refresh. The component table for that row recommends 200 kHz with a 210 k resistor and caps the usable frequency at 250 kHz with 169 k, which is unusual in a family where 3.3 V out can run at 525 kHz.

The practical consequence is a bigger inductor current ripple and a larger output capacitor than the same 5 A would need at 3.3 V. It also means a 24 V rail cannot be pushed to a high frequency to shrink the magnetics, so the module's own 11.25 mm by 15 mm footprint is doing the size saving instead of the switching frequency.

Driving the output setting for 24 V

The ADJ pin is regulated to 1.19 V and the adjust resistor follows RADJ = 11.9 / (VOUT - 1.19) with the result in kohm. For 24 V that is 521.7 ohm, and the 499 ohm value in the component table is the nearest E96 part, which gives about 25 V rather than 24 V.

The gap matters on a 24 V rail that feeds a downstream converter with a 26 V input ceiling. The formula, not the table, is what to calculate from, and a 1 percent resistor at the calculated value keeps a 24 V rail where the load expects it. The ADJ pin itself is specified from 1.16 V to 1.22 V over temperature, which is a 5 percent window before the resistor tolerance is added.

Low output from the same bus

The other end of the range is just as awkward in the opposite direction. At 36 V in and 1.2 V out the duty cycle is 3.3 percent, which is 133 ns of on time at 250 kHz, and the component table caps that row at 250 kHz for the same reason the 24 V row is capped.

The module will not run 1.2 V from 36 V at 1 MHz, and a specification that assumes it will has to be corrected early. A two stage arrangement, 36 V to 5 V and then 5 V to 1.2 V, is the usual answer where a high frequency small footprint rail is needed from a wide input.

What the LGA brings to a 36 V industrial board

The 2.82 mm LGA body leaves room above the module on a card with a 3 mm standoff, and the Au pads suit a tin-lead or a gold finished board without the ball collapse questions that come with SAC305. Thermally the body is 18.6 C/W junction to ambient, the same as the BGA, so the height saving costs nothing in thermal performance as long as the copper under the module is there.

Industrial boards with a 36 V field supply usually need input protection, a reverse polarity diode arrangement and a transient clamp in front of the module, and none of that is inside the package. The 36 V rating is the operating window, not a surge allowance, so a 48 V or a 60 V transient on the field wiring has to be handled before it reaches VIN.

The pages that answer this most often are the power management cross reference for the family alternatives, one stop BOM sourcing for the acceptance test, and OEM procurement for the case where a replacement has to be fitted before the next build.

Two questions buyers ask

Why is the recommended frequency lower for 24 V out? Because the duty cycle is 67 percent and the off time has to stay long enough for the low side and the bootstrap. The component table caps that row at 250 kHz, against 525 kHz for a 3.3 V output.

Is 499 ohm the right adjust resistor for 24 V? It is the value in the component table and it gives about 25 V from the published formula. For a rail that has to stay under a 26 V ceiling, calculate from RADJ = 11.9 / (VOUT - 1.19) instead.