Contact Us

LTM4633IY#PBF

Brand: Analog Devices
Analog Devices LTM4633IY#PBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LTM4633IY#PBF — Analog & Mixed-Signal ICs | Superb Automation

LTM4633IY#PBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LTM4633IY#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LTM4633IY#PBF: three 10 A rails from one 15 mm package, and the 2.375 V input that needs a bias

The LTM4633IY#PBF is a triple 10 A step-down module in a 15 mm by 15 mm by 5.01 mm ball grid array. It runs from 4.7 V to 16 V, or from 2.375 V to 16 V when an external 5 V bias is supplied, and delivers three independent outputs of 0.8 V to 1.8 V on the first two channels and 0.8 V to 5.5 V on the third, each set by one resistor. It holds plus or minus 1.5 percent of total dc error, supports frequency synchronization and multiphase operation on the first two channels, and includes general purpose temperature monitors.

Published values

ParameterValue
Input voltage4.7 V to 16 V, 2.375 V to 16 V with an external 5 V bias
Output 1 and 20.8 V to 1.8 V at 10 A each
Output 30.8 V to 5.5 V at 10 A
DC output errorplus or minus 1.5 percent
Controlcurrent mode, external compensation per channel
Synchronizationfrequency synchronization, multiphase on outputs 1 and 2
Monitorsgeneral purpose temperature monitors, power good per output
Sequencingsoft start and output voltage tracking
Thermal resistance7.5 degree C per W
PackageBGA, 15 mm x 15 mm x 5.01 mm
Protectionoutput overvoltage and overcurrent
FinishRoHS compliant, lead free

Thirty amps and 58 W in a 225 square millimetre package

The common configuration is 1.0 V, 1.5 V and 3.3 V at 10 A each, which is 10 W, 15 W and 33 W, or 58 W in total. At 88 percent the loss is 7.9 W and at 7.5 degree C per W the rise is 59 degree C, so a 60 degree C ambient puts the junction at 119 degree C. That is inside the 125 degree C limit with 6 degree C to spare, which is why the configuration is the one on the front page: it is the largest load that fits without airflow.

The third output is the one that carries the power, because it is the only channel that goes to 5.5 V. At 3.3 V and 10 A it is 33 W, more than half the total, and its loss is correspondingly larger. A build that does not need a high voltage rail is better served by spreading the current across the first two channels, which are limited to 1.8 V but have the same 10 A rating.

Two point three seven five volts input is a bias rail question, not a regulator question

The module's own minimum input is 4.7 V. The 2.375 V figure only applies when a separate 5 V bias is present, because the internal circuitry needs a rail above the input to drive the high side switch. A 3.3 V backplane therefore needs the bias rail, and a 3.3 V backplane without one is outside the part even though 3.3 V is above 2.375 V.

That bias rail also sets the efficiency: the internal drivers draw from it rather than from the input, which is why the low input configuration exists at all. A board that already has a 5 V rail uses it for the bias and can then run from 3.3 V or even 2.5 V, which is the configuration the front page application shows.

Multiphase on two of three channels, and temperature monitors on all three

Outputs one and two can be interleaved as a two phase rail with current sharing, which halves the input ripple at the switching frequency and doubles it at twice the frequency. The third output runs independently, so a build with a heavy core rail and a light 3.3 V rail puts the core on the paralleled pair and the light rail on channel three.

The general purpose temperature monitors are diode connected junctions brought out to pins, so an external measurement of the die temperature is possible without a sense resistor. On a package that runs 59 degree C above ambient at full load, that measurement is the difference between a build that is checked and one that is assumed.

For a board that has to keep running while a reel runs out, the power management cross reference is where the family alternatives sit, OEM procurement is the check list before a substitute goes in, and component lead time solutions is how a gap is covered without a new line item.

Two questions buyers ask

Do all three outputs need external compensation? Each channel has its own external compensation network, and the values depend on the output capacitor and the load step of that rail. A build that copies one network across all three has one channel tuned correctly and two that are either slow or unstable, so the networks are set per rail.

Can the third output be used at 5.5 V from a 5 V input? No. A step-down regulator cannot produce an output above its input, so a 5.5 V output needs an input above 5.5 V plus the dropout, and the 16 V maximum input is what allows it. From a 5 V rail the third channel is limited to about 4.5 V.

The temperature monitor is a diode junction, not a sensor

Each channel brings out a general purpose temperature monitor, which is a diode connected junction inside the package rather than an integrated sensor with a digital output. It is read by forcing a current and measuring the forward voltage, so the accuracy depends on the current source and on the calibration of the junction, not on a factory trimmed part.

On a package that runs 59 degree C above ambient at full load, the monitor is still the only way to know the die temperature without a thermal camera or an infra red measurement. The reading is good enough to catch a rail that is running 20 degree C hotter than the others, which is the failure mode worth catching: a single channel loaded beyond its share shows up as a monitor reading that is out of line with its neighbours long before the module fails.