Contact Us

LTM4632IY#PBF

Brand: Analog Devices
Analog Devices LTM4632IY#PBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LTM4632IY#PBF — Analog & Mixed-Signal ICs | Superb Automation

LTM4632IY#PBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LTM4632IY#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LTM4632IY#PBF: VDDQ, VTT and VTTR for a DDR-QDR4 rail in 0.5 square centimetres

The LTM4632IY#PBF is a triple output step-down module for DDR and QDR4 memory rails: a 3 A VDDQ rail, a 3 A VTT rail that both sources and sinks, and a 10 mA low noise VTTR reference at half of VDDQ. It runs from 3.6 V to 15 V in and 0.6 V to 2.5 V out, and the whole solution is quoted as 0.5 square centimetres on a dual sided board. The I grade is -40 C to 125 C in the 6.25 mm by 6.25 mm by 2.42 mm ball grid array with SAC305 balls.

Published values

ParameterValue
Input voltage3.6 V to 15 V
Output voltage0.6 V to 2.5 V, 1.2 V with a 60.4 k resistor
VDDQ current3 A, sink and source capable
VTT current3 A, tracks VDDQ / 2
VTTR output10 mA buffered reference at VDDQ / 2
Total output error1.5 percent over line, load and temperature
Minimum on time20 ns
Minimum off time45 ns
Junction to ambient20 C/W, 17 C/W to case top
Package6.25 mm x 6.25 mm x 2.42 mm BGA, MSL 3

Three rails, one of which has to sink

A DDR termination rail has to both source and sink current, because the memory bus drives it in both directions depending on the data pattern. The LTM4632 makes VTT a 3 A rail that does exactly that and tracks it to half of VDDQ through an internal divider, so the termination resistors see a rail that follows the memory's own supply rather than a fixed half rail.

The VTTR pin is a separate buffered reference at the same half voltage with 10 mA of drive, which is enough for the reference input of a memory controller and not enough to terminate a bus. A board that loads VTTR with termination resistors has misunderstood the pin, and the 1.5 percent total error on the main rails does not cover the droop that follows.

The on-time floor at 0.6 V out

The minimum on time is 20 ns and the minimum off time is 45 ns. At 15 V in and 0.6 V out the duty cycle is 4 percent, which at 2 MHz is exactly 20 ns of on time and at 3 MHz is 13.3 ns, below the floor.

So a 0.6 V rail from a 15 V input tops out at about 2 MHz whatever the resistor on RT says, while a 1.2 V rail from 12 V at 10 percent duty runs to 4 MHz with room to spare. The floor is a duty cycle limit and it scales with the input voltage, which is why the same module looks fast on a 5 V bus and ordinary on a 12 V one.

Thermal: small package, small loss

At 12 V to 1.2 V and 3 A the output is 3.6 W and about 0.64 W of loss at 85 percent, which on 20 C/W is a 12.7 C rise. Even the 15 V to 0.6 V case at 3 A is 1.8 W out and 0.45 W of loss, a 9 C rise, so this module is thermally relaxed compared with the higher current parts of the family.

The 17 C/W junction to case top is high for the package size, which reflects the 1.82 mm land grid array height in the other body: there is very little material to spread heat. The board is still the heat sink, and the dual sided 0.5 square centimetre claim assumes capacitors on the reverse side as well.

What the 1.5 percent total error covers

The 1.5 percent figure is total output error over line, load and temperature, not a room temperature accuracy. For a 1.2 V memory rail that is 18 mV, which is inside the JEDEC window for DDR4 VDDQ and is the reason the part can be used without a trim step.

The VDDQ rail also has a power good output with a window of about 8 percent to 14 percent of the 0.6 V reference, so a rail that has drifted 5 percent still reads good. That is a fault indicator, not a precision monitor, and a system that needs to know the rail within 2 percent has to measure it rather than read the flag.

For a board that has to keep running while a reel runs out, the power management cross reference is where the family alternatives sit, one stop BOM sourcing is the check list before a substitute goes in, and component lead time solutions is how a gap is covered without a new line item.

Two questions buyers ask

Can the VTT rail be loaded like a normal supply? It can source and sink 3 A, and it tracks VDDQ / 2. It is a termination rail rather than a general purpose supply, so its accuracy and its transient behaviour are specified for that job.

Why will a 0.6 V rail not reach 3 MHz? Because the minimum on time is 20 ns. At 15 V in the duty cycle is 4 percent, so 20 ns corresponds to 2 MHz, and a higher frequency would need a shorter on time than the part can produce.