LT6004IMS8#TRPBF
Product Specifications
LT6004IMS8#TRPBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LT6004IMS8#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
LT6004IMS8#TRPBF: One Microamp per Amplifier and the Drift That Comes With It
The LT6004 is the dual member of a 1.6 V to 16 V op amp family that draws 1 uA per amplifier maximum and still guarantees a 500 uV maximum offset, 90 pA maximum input bias current and 100 dB common mode rejection. It is the part chosen when the budget is set by a battery rather than by bandwidth. What the datasheet summary does not stress is that the offset drift is 2 uV per degree C, which is 330 uV across a 165 degree span and 66 percent of the initial offset limit.
The energy arithmetic
One microamp for a year is 8.76 mAh, and the dual is 17.5 mAh. On a 225 mAh coin cell, a dual running continuously takes the whole cell in 12.8 years at that current alone, which is why this family appears in gas monitors and solar powered nodes that must survive a decade on one cell. Every other load on the board, including the reference and the converter, adds to that number, so the amplifier current is a floor and not a budget.
Drift is the second half of the story. The typical 2 uV per degree C is a typical, not a maximum, and the maximum offset is specified at one temperature. A stage calibrated at 25 C and operated at 85 C moves by 120 uV typical on top of whatever the initial offset was, which is still small against a 12 bit LSB on 3 V (732 uV) and larger than a 16 bit LSB (46 uV).
What 1 uA buys in drive and rejection
Open loop gain is 100,000 minimum driving a 20 kohm load, and the output handles 500 pF of capacitive load, so a cable or a filter capacitor at the output does not turn the stage into an oscillator. Common mode rejection is 100 dB and supply rejection 95 dB, which matters when the same rail feeds a switching converter. The input bias current of 90 pA maximum is what allows a 10 Mohm source without a large offset: 90 pA into 10 Mohm is 0.9 mV, still small against a 12 bit LSB on 3 V.
| Channels | dual, single and quad members in the same family |
| Supply range | 1.6 V to 16 V, specified at 1.8 V, 5 V and plus and minus 8 V |
| Supply current | 1 uA per amplifier maximum |
| Offset voltage | 500 uV maximum, 2 uV per degree C typical drift |
| Input bias current | 90 pA maximum |
| Rejection | 100 dB common mode, 95 dB supply |
| Open loop gain | 100,000 minimum into 20 kohm |
| Capacitive load | 500 pF |
| Temperature and package | minus 40 to plus 125 C, 8 lead MSOP, 3 mm by 3 mm DFN, ThinSOT for the single |
Where it fits
Portable gas monitors, battery or solar powered sensor nodes, micropower active filters and low voltage signal conditioning where the amplifier must not be the load that decides cell life. The 1.6 V minimum supply is unusual and lets a two cell alkaline pack run to end of life without a boost stage. It is not a part for a 1 MHz signal path; the family is built for DC accuracy at almost no current.
Order code and availability
IMS8 is the industrial grade in the 8 lead MSOP, and the same silicon is offered in a 3 mm by 3 mm DFN for boards where the package height matters. Family coverage is on the analogue and mixed signal line card.
Common questions
Does the 1 uA figure include the output stage? It is the quiescent current of the amplifier with no load. Driving a 20 kohm load to mid rail adds the load current, so the budget on a 3 V rail is 1 uA plus 75 uA for that load, and the load is usually the larger term.
Is 500 pF of capacitive load a hard limit? It is the load the part is specified to drive without a series resistor. Above that a small series resistor at the output keeps the loop stable, at the cost of a pole that has to be checked against the feedback network.
Cost comparisons across micropower amplifiers are on the component cost reduction page, and substitution checks are on the amplifier cross reference page.
LT6004IMS8#TRPBF: the divider around it draws more than the amplifier, and that decides the battery life
A one microamp amplifier is bought for a budget that the surrounding resistors can spend before the amplifier gets a chance. A window comparator built from a 1 microamp part and a 1 megohm divider is a 1.5 microamp circuit, and the part's own contribution is a third of it. This block works the budget for a 3 V always-on threshold detector, then shows what a high impedance divider does to the offset once the resistors are made large enough to matter.
Count the divider before the amplifier
Two 1 megohm resistors across 3 V draw 1.5 uA continuously. Two 10 megohm resistors draw 0.15 uA, two 15 megohm draw 0.1 uA, and two 22 megohm draw 0.068 uA. On a 220 mAh coin cell, a 3 uA total budget lasts 8.4 years and a 2 uA budget lasts 12.6 years, so the difference between a 1 megohm and a 15 megohm divider is the difference between a product that meets a ten year promise and one that does not. The amplifier at one microamp per amplifier is already a small term beside a divider that was chosen without arithmetic.
Large resistors turn bias current into offset
A 15 megohm source impedance multiplies the input bias current into an offset. At 3 nA that is 45 mV, which is larger than most thresholds a detector is built around; at 0.3 nA it is 4.5 mV. That is why the same circuit cannot be made both low current and precise with the same part: the divider that saves the microamps costs millivolts, and the answer is either a part with a much lower bias current or a switched divider that is only powered while a measurement is taken. A third option is a capacitor across the lower resistor, which holds the threshold while the divider is off and is the usual trick in a wake and measure product.
What one microamp buys in drive and rejection
At one microamp of supply the output can source tens of microamps, so the load has to be a comparator input or an ADC sample and hold, not a divider or an LED. The capacitive load it can drive is correspondingly small, and a 100 pF cable on the output will ring unless a series resistor is added. The rejection is a slow loop at this current, so a supply step takes milliseconds to disappear from the output, which is fine for a battery monitor and not fine for a threshold that must respond to a fault within a microsecond.
| Divider pair | Current at 3 V | Years on 220 mAh | Offset at 3 nA bias |
|---|---|---|---|
| 2 by 1 megohm | 1.5 uA | 16.7 | 3 mV |
| 2 by 10 megohm | 0.15 uA | 167 | 30 mV |
| 2 by 15 megohm | 0.10 uA | 250 | 45 mV |
| 2 by 22 megohm | 0.068 uA | 369 | 66 mV |
Quiescent current across the amplifier family is compared on amplifier cross reference, the grade and temperature code differences are on pin to pin cross reference, and the passives that set the threshold are quoted through one stop BOM sourcing.
Request Quote — In Stock, 100% New & Original, Full Warranty