Contact Us

LT3090EMSE#TRPBF

Brand: Analog Devices
Analog Devices LT3090EMSE#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3090EMSE#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3090EMSE#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3090EMSE#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3090EMSE#TRPBF: extended grade of the 600 mA negative regulator

The LT3090EMSE#TRPBF is the extended grade of the negative 600 mA regulator in the 12-lead MSOP, supplied on tape and reel. It is rated -40 C to 125 C at the junction, which is the same window as the industrial grade of this part, and it carries the identical electrical table: -1.5 V to -36 V input, 0 V to -32 V output from one SET resistor, 50 uA SET current with 1 percent initial accuracy, 300 mV typical dropout at 600 mA, 18 uV RMS noise over 10 Hz to 100 kHz and 85 dB of rejection at 120 Hz.

Published values

ParameterValue
Input voltage-1.5 V to -36 V
Output voltage0 V to -32 V
Output current600 mA
SET pin current50 uA, 49 to 51 uA over the range
Dropout voltage185 mV at 1 mA, 300 mV at 600 mA
GND pin current1 mA at no load, 11.5 mA at 600 mA
Output noise18 uV RMS, 10 Hz to 100 kHz
Load regulation1.2 mV from 1 mA to 600 mA
Thermal resistance34 C/W junction to ambient, 5.5 C/W to case
Package and grade12-lead MSOP, -40 C to 125 C, tape and reel

Extended against industrial on this family

On many Linear Technology families the E grade is tested at 25 C with pulse loads and the I grade is guaranteed over the full operating window, which is why the two codes carry different prices for the same die. On the LT3090 both the E and the I code are specified -40 C to 125 C, and the numbers in the table above are the guaranteed ones for either. A buyer comparing them should therefore treat the difference as a commercial and test-flow question rather than an electrical one, and should only move to the H or MP code when the junction really has to go past 125 C.

Rejection at the switching frequency

The negative rail on most boards is post-regulated from a charge pump or an inverting switcher running between 300 kHz and 2 MHz. At 120 Hz the part rejects 85 dB, at 10 kHz it rejects 50 dB, and at 1 MHz the figure falls to 20 dB. That last number is the one that decides whether a second filter stage is needed: a 20 dB figure removes ninety percent of the switching residue, which is usually enough to hold a converter or an amplifier input quiet, but it is not enough to clean up a poorly damped charge pump on its own. Reading the three figures together is more useful than reading the headline number, because the audio-band figure says nothing about what happens at the converter frequency.

Current limit that protects the wiring

The ILIM pin takes a resistor and sets a foldback limit on the output current, so the regulator can be made to protect a cable or a connector rather than only itself. The internal backup limit stays in place behind the programmed value, so a fault on the ILIM pin does not remove protection entirely. For a negative rail feeding a remote sensor over a long lead this is the practical way to keep a short at the far end from cooking the regulator, and it works together with the current monitor pins, which report what the load is actually drawing.

Order code and stock

EMSE is the extended grade in the MSOP on tape and reel; the industrial grade of the same body is IMSE and the DFN equivalent is EDD. All of them are the same die with a different test flow and a different label, so a shortage on one grade is usually solved by moving up or sideways rather than by qualifying a new part. The lead time page carries the current schedule for the MSOP body, the cost reduction page covers volume pricing across grades, and vendor consolidation covers keeping the negative rails on one supplier line.