LT3071EUFD#PBF
Product Specifications
LT3071EUFD#PBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LT3071EUFD#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LT3071EUFD#PBF: tray quantity for the 5 A low dropout rail
The LT3071EUFD#PBF is the same 5 A regulator as the taped code, in the 28-lead 4 mm by 5 mm QFN, extended grade, supplied in trays. It holds 0.8 V to 1.8 V in 50 mV steps, offers plus or minus 10 percent analog margining, reaches 85 mV of dropout at 5 A, runs at 25 uV RMS of noise and needs 15 uF of ceramic output capacitance. The reason to order the tray form is a first article or a lab build, where a reel is more parts than the project needs.
Published values
| Parameter | Value |
|---|---|
| Output current | 5 A |
| Output voltage | 0.8 V to 1.8 V, 50 mV steps |
| Dropout voltage | 85 mV typical at 5 A |
| Bias supply | 0.95 V to 3.0 V |
| Accuracy | Plus or minus 1 percent |
| Current monitor | Load current divided by 2500 |
| Output noise | 25 uV RMS, 10 Hz to 100 kHz |
| Rejection | 30 dB at 1 MHz |
| Minimum output capacitor | 15 uF ceramic, 47 uF input bypass recommended |
| Thermal resistance | 30 C/W on 2500 square millimetres |
| Package and grade | 28-lead QFN, tray, -40 C to 125 C |
Fifteen microfarads, not one
The capacitor requirement is the detail that catches boards reused from an older regulator. Fifteen microfarads of ceramic is a large part for a 1 V rail, and it is specified as a minimum for stability rather than as a recommendation. A board ported from a part that needed 10 uF may oscillate, and the oscillation shows up as a rail that looks fine on a meter and fails on a scope. The input side wants about 47 uF to hold the impedance low across frequency, because the regulator's loop depends on a low impedance source. Both figures are worth carrying into the drawing review.
The tray, the reel and the first article
A tray part is the practical unit for a bench build: it can be placed by hand, it does not need a feeder, and a small quantity can be ordered without committing to a reel. Once the rail is characterised, the taped code takes over for the line. Because the die and the pinout do not change, the characterisation work carries over, and the only thing that changes is the packing. That is the reason both codes exist in the catalogue rather than only the reel.
Margining in a production test
The analog margining pin makes it possible to sweep the rail by plus or minus 10 percent without touching the digital setting, which is exactly what a production test wants when it checks that a downstream device still works at the tolerance limits. The reference moves around a 600 mV nominal, so the sweep is continuous and the test does not have to step through the digital codes. For a board with several rails, the same signal can drive several margining pins at once, provided the rails have the same nominal.
Order code and stock
The PBF suffix is the tray; EUFD#TRPBF is the extended grade reel, IUFD the industrial grade and MPUFD the -55 C to 125 C version. The exposed pad is ground, so the thermal path is the ordinary one for a QFN and no isolation is needed. The one stop BOM page covers ordering the part with its 15 uF and 47 uF capacitors on one line, the ADI second source page lists the grade options, and the cost page shows the volume difference between tray and reel.