Contact Us

LT3065MPMSE#TRPBF

Brand: Analog Devices
Analog Devices LT3065MPMSE#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3065MPMSE#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LT3065MPMSE#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3065MPMSE#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3065MPMSE#TRPBF: 500 mA at 45 V input in the 12-lead MSOP, minus 55 C grade

The LT3065MPMSE#TRPBF is the widest temperature grade of the LT3065, a 500 mA low dropout regulator that works from a 1.6 V to 45 V input and holds any output between 0.6 V and 40 V. The MPMSE code is the 12-lead MSOP on tape and reel, rated minus 55 C to 150 C at the junction and tested over that whole window rather than sampled at one point. Three pins separate it from a plain three terminal regulator: a resistor on IMAX sets the current limit to plus or minus 10 percent, PWRGD reports when the output is inside regulation, and a capacitor on REF/BYP sets both the noise floor and the soft start ramp.

Published values

ParameterValue
Input voltage1.6 V to 45 V, 2.2 V maximum at 500 mA
Output voltage0.6 V to 40 V adjustable, ADJ tied to OUT gives 0.6 V
Output current500 mA, external limit accurate to plus or minus 10 percent
Dropout voltage110 mV at 10 mA, 220 mV at 100 mA, 300 mV at 500 mA typical
GND pin current55 uA no load, 1.8 mA at 100 mA, 11 mA at 500 mA
Output noise90 uV RMS bare, 25 uV RMS with 10 nF on REF/BYP
Ripple rejection70 dB minimum at 120 Hz, 85 dB typical
ADJ pin bias current16 nA typical, 60 nA maximum
PWRGD trip point90 percent of nominal, 86 to 94 percent over temperature
Reverse output current10 uA maximum with the input grounded
Thermal resistance28 C/W junction to ambient, 6 C/W to case
Grade and package12-lead MSOP, minus 55 C to 150 C, tape and reel

What the MP grade is tested against

The four grades of this part are not the same claim. The E grade is tested at 25 C and its performance from 0 C to 125 C is guaranteed, with minus 40 C assured by characterization only. The I grade is guaranteed over minus 40 C to 125 C. The H grade is tested at 150 C. The MP grade is tested over the full minus 55 C to 150 C window, which is the one that matters when the board sits in an enclosure that is soaked at minus 40 C before power is applied and the regulator has to start into a load that is still cold. Two practical consequences follow. A buyer who has been running an I grade and sees a price jump on the MP code is paying for test coverage, not for a better die, so a change in the other direction is a documented risk rather than a drop in replacement. And the 150 C junction rating is not a licence to run there: the vendor states that operating lifetime is derated above 125 C, so a board that parks at 140 C trades years for watts.

The 500 mA figure and the input floor

Two numbers in the table are often read as one. The input range starts at 1.6 V, but the regulated output specification at 500 mA is written from 2.2 V, because below that the pass element is in dropout no matter what the setpoint says. On a 3.3 V rail that distinction costs nothing. On a two cell lithium pack whose end of discharge is 2.5 V it decides whether the downstream 1.8 V rail stays in regulation at full load or sags with the battery. The 45 V ceiling is the other end: the part is aimed at 24 V and 48 V industrial buses where load dump and inductive kick push a nominal 24 V rail past 40 V, and the input pin is rated to plus or minus 50 V absolute, with reverse battery protection quoted as 300 uA of leakage at minus 45 V.

Setting the current limit with a resistor

The IMAX pin converts a resistor to a current limit, and the tolerance is plus or minus 10 percent across input voltage and temperature, which is tight enough to use as a protection threshold rather than a guess. A 1.5 kOhm resistor gives about 200 mA and a 604 Ohm resistor about 495 mA, so the same order code serves a 200 mA sensor rail and a 500 mA logic rail with one line item change. If the feature is unwanted, the pin goes to ground and the internal limit, 520 mA minimum, takes over. That internal limit folds back with input to output differential, so a shorted output at 40 V input does not sit at half an amp in the pass element: the vendor publishes current limit against differential for exactly this reason, and any thermal calculation that assumes the full limit at full differential will be wrong.

Noise, PWRGD and the rest of the pinout

The bare part is a 90 uV RMS regulator from 10 Hz to 100 kHz. With a 10 nF capacitor from REF/BYP to ground the figure falls to 25 uV RMS at a 0.6 V output, and the same capacitor sets the soft start ramp, which is why one component appears in two sections of the data sheet. Above 0.6 V the divider amplifies the reference noise, and the vendor's answer is a feedforward capacitor from OUT to ADJ, doubled whenever the divider current is doubled. The ADJ pin draws 16 nA out of the pin, so R1 is capped at 62 kOhm to keep 10 uA in the divider and hold that error small. PWRGD is an open drain output that pulls low when the output is below 90 percent of nominal, with 1.6 percent of hysteresis, and it sinks 0.07 V at 50 uA while leaking 0.01 uA at 45 V, so it can hang off a 3.3 V logic rail directly.

Sourcing the MP code

Wide temperature ADI linear parts are the first line to go short, because the automotive and avionic programs take the H and MP grades first and the catalogue distributors stock the E and I codes. Files that carry several of these rails benefit from keeping the whole family on one cross reference, which is what the power management cross reference covers. Consolidated buying across those lines sits on the one stop BOM sourcing page, and scheduling for the MSOP body is on the lead time page.