LT1761ES5-5#TRPBF
Product Specifications
LT1761ES5-5#TRPBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LT1761ES5-5#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
LT1761ES5-5#TRPBF: a fixed 5 V regulator that cannot be fed from a 5 V rail
What this order code is
LT1761ES5-5#TRPBF is the fixed 5 V option of the LT1761 family in the 5-lead TSOT-23 body, E grade, on a reel with a lead free finish. The die is the same micropower low dropout regulator as the 3.3 V code, with a different trimmed reference, so every figure in the family table applies: 20 uA quiescent, 300 mV of dropout at 100 mA, 20 uV RMS of noise with the reference bypassed, stable with 1 uF, reverse battery protected without an external diode.
The 5 V option exists for one reason: a 5 V load that has to be produced from a higher rail, usually 12 V in industrial equipment or a 9 V to 15 V adapter, and where a switching supply would put too much ripple on the node. It is also the option people order by mistake for a 5 V input, which is why the headroom arithmetic below matters more here than on any other code in the family.
Parameters as published
| Item | Value |
|---|---|
| Output voltage | 5 V fixed |
| Output current | 100 mA |
| Input voltage range | 1.8 V to 20 V |
| Dropout at 100 mA | 300 mV |
| Minimum input for regulation | 5.3 V |
| Quiescent current | 20 uA |
| Shutdown current | below 0.1 uA |
| Output noise with bypass | 20 uV RMS, 10 Hz to 100 kHz |
| Output capacitor | 1 uF ceramic |
| Protection | current limit, thermal limit, reverse battery |
| Body | 5-lead TSOT-23 |
| Grade | E |
| Packing | reel, lead free |
Numbers that decide the application
A 5 V output needs 5.3 V at the input at full load, so a 5 V rail at minus five percent, which is 4.75 V, is 550 mV short and the output sits at about 4.75 V minus the dropout, not at 5 V. Sellers of 5 V adapters and USB supplies run into this constantly: the regulator is not boosting anything, it is dropping, and it needs something to drop. A 12 V rail is the natural input, and a 9 V rail at minus ten percent, 8.1 V, still leaves 2.8 V of headroom.
That headroom becomes heat at the rate of 1.4 mW per milliamp at a 9 V input and 7 mW per milliamp at 12 V. At 100 mA from 12 V the part dissipates 0.70 W, which is a rise of about 175 C in a 5-lead TSOT-23 and outside the package for any normal ambient. The same board at 20 mA dissipates 0.14 W and rises about 35 C, which is why a 12 V to 5 V analog node on this part is a tens of milliamps job and not a hundreds of milliamps job. Above roughly 30 mA from 12 V, a small buck followed by this regulator is the cheaper thermal answer than a bigger linear part.
The noise is the reason to keep the linear stage. 20 uV RMS against a 5 V full scale is 0.26 LSB of a 16 bit converter and 1.0 LSB of an 18 bit one, and the low dropout means the part can sit directly after a switching stage without the 3 V of headroom an older regulator would need. The 20 uA of quiescent current survives the sleep state at 0.175 Ah a year, which matters when the 5 V rail stays alive to keep a real time clock and a comparator running.
Where it fits and where it does not
It fits 12 V or 9 V industrial rails that need a quiet 5 V node for converters, references, op amps and small signal chains, and it fits an adapter input where the load is tens of milliamps. It does not fit a 5 V input, a USB input, or a 3.3 V system, and it does not fit a 24 V bus, which is above the 20 V ceiling before any tolerance is applied and above the 30 V a load dump would apply.
Supply and second source questions
Two fields get confused on this code. The first is the input voltage: buyers see the 1.8 V to 20 V range and assume a 1.8 V input works for a 5 V output, which it cannot. The second is the grade letter, because the same 5 V die ships as E and I and the ordering table, not the product page, carries the temperature limits for each. Substitutes that claim the same footprint often publish their dropout at a lower current, so a part quoted at 300 mV at 100 mA and a part quoted at 200 mV at 50 mA are not the same regulator on a 100 mA load. The families that hold the same pinout are listed on the power management cross reference page.
Sourcing notes and next step
We quote the exact code, not the family, because four order codes share this body and only one of them is 5 V. Send the line items with quantities and the required date through the BOM shortage recovery page and we will answer with availability and, where the exact code is short, with the honest position rather than a lookalike part. The wider regulator list sits on the analog and mixed signal IC page.
Request Quote — In Stock, 100% New & Original, Full Warranty