Contact Us

HMC998APM5E

Brand: Analog Devices
Analog Devices HMC998APM5E is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HMC998APM5E — Analog & Mixed-Signal ICs | Superb Automation

HMC998APM5E

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The HMC998APM5E from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

HMC998APM5E: the 2 W die in a surface mount package, and what changes

The HMC998APM5E is the surface mount order code for the dc to 22 GHz, two watt amplifier that the HMC998A die document describes: 33.5 dBm saturated, 32.5 dBm at one decibel compression, 14.5 dB of gain and 43 dBm of output third order intercept from a 15 V supply at 500 mA quiescent. The electrical figures in that document are die figures, taken with two 0.025 mm bond wires of 0.31 mm length, so a buyer taking the packaged code has to add the package transition to the list of things that move.

Published values

ParameterValue
Amplifierdc to 22 GHz pHEMT distributed power amplifier
Saturated output power33.5 dBm typical, published as a die value
Output power at one decibel compression32.5 dBm typical
Gain14.5 dB typical
Output third order intercept43 dBm typical
Supply15 V at 500 mA quiescent
Dissipation at saturation5.26 W
Reference conditiontwo 0.025 mm bond wires, 0.31 mm length
Package formsurface mount, order code PM5E
Thermal paththrough the package paddle rather than the die backside alone

What the package adds and what it takes away

In die form the radio frequency path from the board to the transistor is a bond wire, and the data sheet says the values are taken with a 0.31 mm wire. In the package that wire is replaced by an internal transition plus the solder joint to the board, which at 22 GHz is a small amount of loss and a small amount of inductance. Both change the match, and neither is usually large enough to matter at the one decibel level.

What the package takes away is the ability to tune that transition, and what it adds is a defined thermal path and a part that any surface mount line can place. For a programme that does not want to own a die attach and wire bond process, that is the whole argument, and it is worth more than the fraction of a decibel.

The thermal budget does not change

15 V at 500 mA is 7.5 W of DC input against 2.24 W of saturated output, so 5.26 W is dissipated whichever form the part takes. The path changes: in die form it goes through the backside and the attach, and in the package it goes through the paddle and the solder joint. The temperature the channel reaches depends on the whole stack, and a package with a good paddle on a board with a poor via field is worse than a die on a good carrier.

Five watts in a small package is where a lot of builds quietly fail. The junction to case figure for the package has to be combined with the board's own thermal resistance, and the sum is what decides whether the 500 mA quiescent point stays where it was set. If the case runs 30 degrees hotter than the bench, the drain current at a fixed gate voltage rises, and the dissipation rises with it.

What to confirm before the order code is released

Three items: the package outline and paddle size against the board footprint, the thermal resistance from junction to case as published for the packaged part rather than the die, and the pin function arrangement against the die pads. A substitution between die and package is not drop in even when the amplifier inside is the same.

The fourth item is availability. Die and packaged codes have separate stock positions and separate last time buy notices, and a programme that has qualified one form should know what the other form costs to qualify before it needs to.

Buyers usually arrive at the pin to pin cross reference to find the family alternatives, then use how to verify a drop in replacement to confirm a substitute before it is fitted; component lead time solutions is the routine for a part that has already stopped shipping.

Two questions buyers ask

Does the packaged part have the same electrical performance as the die? The amplifier is the same, so the gain, power and intercept are close. The package adds a transition and changes the thermal path, and the published electrical figures belong to the die document, so the packaged figures should be taken from the package document.

Is 5.26 W of dissipation a problem in a surface mount part? It is manageable with a proper paddle, a via field and copper, and it is the same 5.26 W the die has to remove. The board thermal resistance is what decides whether the channel stays inside its limit.