Contact Us

HMC462LP5

Brand: Analog Devices
Analog Devices HMC462LP5 is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HMC462LP5 — Analog & Mixed-Signal ICs | Superb Automation

HMC462LP5

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The HMC462LP5 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

HMC462LP5: 2.5 dB noise figure from 2 GHz to 20 GHz in a 5 mm package

The HMC462LP5 is a gallium arsenide pHEMT distributed low noise amplifier in a 5 mm x 5 mm leadless surface mount package, covering 2 GHz to 20 GHz with 13 dB of gain and a 2.5 dB noise figure at 10 GHz. It is self biased from a single 5 V supply at 66 mA, which is what makes it practical as a first stage in a receiver front end rather than as a laboratory amplifier.

Published values

ParameterValue
Frequency range2 GHz to 20 GHz
Noise figure at 10 GHz2.5 dB typical
Noise figure, 2 to 6 GHz3.0 dB minimum, 4.0 dB maximum
Noise figure, 14 to 20 GHz4.0 dB minimum, 6.0 dB maximum
Gain13 dB typical, 12 dB minimum at the band edges
Gain flatness0.5 dB from 6 to 18 GHz
Output power at 1 dB compression14.5 dBm at 10 GHz, 12 to 15 dBm at 2 to 6 GHz
Output third order intercept26 dBm at 2 to 6 GHz, 22 dBm at 14 to 20 GHz
Supply5 V at 66 mA, self biased, 84 mA maximum
Input and output match50 ohm, internally dc blocked
Package5 mm x 5 mm leadless surface mount, 25 square millimetres

Cascading it, in numbers

A 2.5 dB noise figure is a noise factor of 1.78, and 13 dB of gain is a power ratio of 20. A second stage with a 6 dB noise figure, which is a factor of 3.98, adds (3.98 - 1) divided by 20, or 0.149 to the factor, taking the total from 1.78 to 1.93. That is 2.85 dB, so the second stage costs 0.35 dB of the receiver's noise figure.

The same arithmetic run with a 2 dB first stage noise figure gives 2.45 dB at the input and 2.78 dB for the pair, which is why the front end stage is where the money goes. It also shows why a receiver with a filter and a switch ahead of the amplifier cannot reach 2.5 dB: the loss in front of the first stage adds directly.

Self biased and internally dc blocked

A single 5 V rail at 66 mA with no gate supply means the amplifier can be placed anywhere on a board that has 5 V, and a receiver front end with four of them in different bands does not need four sequencers. The internally dc blocked ports remove the blocking capacitors, which at 20 GHz are themselves a loss and a mismatch.

The 66 mA typical and 84 mA maximum are worth noting because the spread is 27 percent. A rail that is budgeted at 66 mA per amplifier and then carries several of them will be under sized at the maximum, and the symptom is a voltage droop that looks like gain compression.

Noise figure across the band, not at one point

2.5 dB at 10 GHz is the headline, and the table gives 3.0 to 4.0 dB at 2 to 6 GHz and 4.0 to 6.0 dB at 14 to 20 GHz. A receiver specified at 2.5 dB across the band is therefore specified at a figure the part only holds in the middle of the band, and the specification has to be written per band segment or with a worst case number.

The rise at the low end is the input matching network, which on a distributed amplifier is an artificial transmission line and cannot be optimised everywhere at once. The rise at the high end is the gate resistance and the line loss, and neither can be tuned out at the module level.

Compression and intercept

14.5 dBm at 1 dB compression at 10 GHz is modest, and it is the correct value for a low noise first stage: a receiver front end that needs more than that puts the amplifier after the first filter, or adds a limiter. Driving this part to 14.5 dBm output with 13 dB of gain means 1.5 dBm at the input, which is a strong signal.

The intercept falls from 26 dBm at the low end to 22 dBm at the high end, so a receiver that has to survive a large blocker at 18 GHz has 4 dB less margin than the same receiver at 3 GHz. That is worth knowing when the blocking specification is written for the whole band.

When an order code in this family cannot be found, the amplifier cross reference lists what else does the same job, medical device components covers what to check before a part is dropped into an existing board, and one stop BOM sourcing is the route we take on a live shortage.

Two questions buyers ask

Is the HMC462LP5 self biased? Yes. It runs from a single 5 V supply at 66 mA typical, 84 mA maximum, with no gate supply and with internally dc blocked input and output ports.

What noise figure should be used in a system budget at 18 GHz? The table gives 4.0 dB minimum and 6.0 dB maximum from 14 to 20 GHz, against 2.5 dB typical at 10 GHz. Use the segment figure for the band the receiver actually covers.