Contact Us

ADM809SARTZ

Brand: Analog Devices
Analog Devices ADM809SARTZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADM809SARTZ — Analog & Mixed-Signal ICs | Superb Automation

ADM809SARTZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADM809SARTZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

ADM809SARTZ: 2.93 V reset monitor in a three lead package

The ADM809SARTZ is a three terminal reset supervisor in a SOT-23 that holds a processor in reset until the supply reaches 2.93 V and keeps it there for 240 ms afterwards. The S suffix is the threshold option and the RT package code is the three lead plastic body, so this order code is the smallest member of a family whose only job is to stop a processor from running below its specified supply.

Published values

ParameterValue
Reset threshold2.89 V minimum, 2.93 V typical, 2.96 V maximum at 25 C
Threshold temperature coefficient30 ppm per C
Reset timeout240 ms typical after the rail crosses the threshold
Reset validguaranteed down to VCC of 1 V
Outputactive low, push pull on the ADM809
Package and range3-lead SOT-23, -40 C to +125 C

A 70 mV threshold window is the whole specification

The three numbers, 2.89 V, 2.93 V and 2.96 V, are a total window of 70 mV at 25 C. Against a 3.3 V rail at minus 5 percent, which is 3.135 V, the margin from the top of the window is 175 mV, or 5.3 percent of nominal. That is the space in which supply ripple, load steps and the threshold drift all have to fit.

The drift is 30 ppm per C, which over a 125 C span is 3750 ppm, or 0.375 percent, or 11 mV on a 2.93 V threshold. That is small against the 70 mV initial window, so the window rather than the drift is what the board has to accommodate. This is the opposite of a cheap supervisor whose threshold moves by 2 percent over temperature and fires on a legal rail.

The rail this threshold does not fit

On a 3.0 V rail at minus 5 percent, which is 2.85 V, the threshold is 80 mV above the rail. The part therefore asserts reset on a supply that is still inside its specification, and the processor is held off for no reason. The 3.08 V option is the part for a 3.0 V rail; the 2.93 V part is the 3.3 V part.

This is the check that decides most orders in this family: read the rail, read the tolerance, then pick the suffix. A purchasing system that substitutes by package and pin count alone will occasionally put a 3.08 V part on a 3.3 V board, where the margin falls to 55 mV and the monitor fires on a legitimate supply dip.

240 ms and the reset pulse

240 ms is long enough for a crystal oscillator to start and for a switching supply on the same rail to reach regulation, and short enough that a power cycle does not look like a hang. The delay is generated internally with no external capacitor, which is the reason a three lead package is enough.

The output is push pull and active low, so it drives the reset pin of a processor without an external resistor. The open drain variant of the same family carries a Z suffix and needs a pull up; mixing the two on one board is a common cause of a reset line that never rises.

Second source notes

Because the part is three leads and does everything internally, the substitution risk is almost entirely in the suffix: threshold value, output polarity and open drain against push pull. A candidate with the same SOT-23 footprint and a different suffix will fit and will not behave the same way.

The pages below hold the power management cross reference, the delivery options for a part that has gone short, and the acceptance sequence for a substitute.

Buyers usually arrive at the power management cross reference to find the family alternatives, then use the pin to pin cross reference to confirm a substitute before it is fitted; component lead time solutions is the routine for a part that has already stopped shipping.

Two questions buyers ask

Is the ADM809SARTZ the same as the ADM810SARTZ? No. The ADM809 output is active low, the ADM810 output is active high. The threshold options and the package are shared.

Does it need an external delay capacitor? No. The 240 ms timeout is internal, which is why the part has three pins and no timing pin.