ADG732BSUZ
Product Specifications
ADG732BSUZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADG732BSUZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADG732: Thirty-Two Inputs Into One Node at 4 Ohms
The ADG732 is a single 32-to-1 analog multiplexer in a 48-lead TQFP or a 48-lead LFCSP, built on a switch element whose on resistance is 4 ohms at 25 C on a 5 V single supply or a plus or minus 2.5 V dual supply, with 0.5 ohm of flatness across the signal range. It runs from 1.8 V to 5.5 V single supply, switches in 23 nanoseconds typical, takes TTL and CMOS compatible control inputs and passes signals rail to rail. The sibling ADG726 in the same package is the dual 16-to-1 version, so one board can carry either a 32 channel single ended array or a 16 channel differential array without a change to the package footprint.
The difference between 4 ohms and 100 ohms in a multiplexer
On resistance is the number that decides what a multiplexer does to the signal. At 4 ohms the switch is a small error term in front of a 1 megohm converter input, and the leakage current through the off switches is the dominant error. At 100 ohms the same switch forms a divider with the source impedance and adds thermal noise, and a 10 kohm source with a 100 ohm switch looks like a 10 kohm source with a 1 percent gain error that moves with temperature. A low on resistance also means the switch can drive a sampling converter directly through its hold capacitor without a buffer, provided the charge transfer settles inside the acquisition window, and that is the case this part was built for.
Values at a glance
| Parameter | Value | Note |
|---|---|---|
| Configuration | Single 32-to-1 | ADG726 is dual 16-to-1 in the same package |
| On resistance | 4 ohms at 25 C | Measured on a 5 V single or plus or minus 2.5 V dual supply |
| Flatness | 0.5 ohms at 25 C | Across the signal range, the term that causes distortion |
| Supplies | 1.8 V to 5.5 V single, plus or minus 2.5 V dual | Rail to rail signal handling |
| Transition time | 23 nanoseconds typical | Break before make |
| Supply current | 10 microamps typical at 5.5 V | 5 microamps at 3.3 V |
| Control | Five address lines plus enable, TTL and CMOS compatible | 1-of-32 decoder on chip |
| Packages | 48-lead TQFP, 48-lead 7 mm by 7 mm LFCSP | Same pinout for the ADG726 and ADG732 |
Channel count against channel quality
Thirty two channels on one die is a routing decision as much as an electrical one. A 32 channel data acquisition card built from four 8-to-1 multiplexers needs four packages, four sets of address decoding and a way to combine their outputs, and the combining network adds capacitance to the node that the converter sees. One 32-to-1 switch puts every channel on the same node, so the parasitic capacitance is one switch plus the bus, and the settling behaviour is the same for every channel rather than depending on which multiplexer it came from. The trade is that the on resistance of a 32 channel switch is higher than an 8 channel one on the same process, and at 4 ohms this part closes most of that gap.
Optical, medical and test equipment use
Optical module arrays, medical instrumentation and automatic test equipment are the three applications where the combination of channel count and low on resistance matters. In an optical system the switch selects between photodiode channels whose transimpedance amplifiers are already on the board, and a switch in front of the amplifier sees a low impedance node where its on resistance is irrelevant and its leakage is everything. In medical instrumentation the switch selects between electrode pairs and the leakage current through off channels sets the baseline drift. In test equipment the switch is part of a scan path and the transition time sets the throughput. The same part serves all three, and what changes between them is the amplifier behind it, not the switch.
Procurement and second source
Multiplexer substitution is deceptively difficult: a part with the same channel count but a different on resistance, address decoding or break before make behaviour will run and will corrupt readings in a way that appears random. The ADC DAC cross reference lists the switches that feed converters in this library, pin to pin cross reference covers the substitutions that need no board change, and the obsolete part cross reference hub is the place to start when a package or a channel count disappears from the catalogue.