ADG1436YRUZ
Product Specifications
ADG1436YRUZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADG1436YRUZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADG1436YRUZ: a dual SPDT with 1.5 ohm on resistance and 260 mA per channel in TSSOP
The ADG1436YRUZ is a dual changeover switch on the iCMOS process with the low resistance die of the ADG1404 family: 1.5 ohm typical, 2.6 ohm maximum over temperature, 0.3 ohm flatness, 0.1 ohm channel match, and a continuous current rating of 260 mA per channel in the TSSOP package and 400 mA in the LFCSP. It is specified at plus or minus 15 V, +12 V and plus or minus 5 V with no logic supply.
Published values
| Parameter | Value |
|---|---|
| Configuration | two independently selectable SPDT switches |
| On resistance | 1.5 ohm typical, 2.6 ohm maximum over temperature |
| Flatness | 0.3 ohm |
| Channel match | 0.1 ohm |
| Continuous current | 260 mA per channel in TSSOP, 400 mA in LFCSP |
| Supply | plus or minus 15 V, +12 V or plus or minus 5 V |
| Package | 16-lead TSSOP or 4 mm x 4 mm LFCSP |
The package sets the current rating
The same die is published with two current ratings: 260 mA in the TSSOP and 400 mA in the LFCSP. The difference is the thermal path, not the silicon. At 260 mA through 2.6 ohm the drop is 0.68 V and the dissipation is 176 mW; at 400 mA the drop is 1.04 V and the dissipation is 416 mW. A 16-lead TSSOP can hold 176 mW at ordinary ambient and cannot hold 416 mW without help, which is exactly why the leadless package carries the higher number.
This matters when a part is substituted between packages on a shortage: the electrical table is identical and the current rating is not. A board that runs at 350 mA and was built with the LFCSP will overheat its TSSOP substitute even though the switch is the same.
Two changeover switches, two uses
A dual SPDT is the shape of a polarity reversal, a range change or a redundant path selection. For a shunt range change the 1.5 ohm resistance is small against a 100 ohm shunt and the flatness of 0.3 ohm is a 0.3 percent gain modulation, which is acceptable on a 12 bit measurement and marginal on a 16 bit one.
For a signal path that carries no current, the low resistance is not needed and a 120 ohm part with picocoulomb charge injection is the better choice. The ADG1436 is bought for the case where the switch sits in series with something that draws milliamps.
Break before make and control
Both switches break before make, so a pole can move between two sources without shorting them. The enable input exists on the LFCSP package and turns both switches off, which is the isolation state during power down.
The digital inputs accept 3 V logic with no separate logic rail, so a 3.3 V microcontroller drives them directly and the analog side can run at plus or minus 15 V. The control line should not be run beside an analog trace: the switching transient is the moment the measurement is settling, and coupling into a high impedance node at that instant is a repeatable offset that looks like a channel error.
For a board that has to keep running while a reel runs out, how to reduce component cost is where the family alternatives sit, one stop BOM sourcing is the check list before a substitute goes in, and BOM shortage recovery is how a gap is covered without a new line item.
Two questions buyers ask
Can the TSSOP version replace the LFCSP version? Electrically the switch is the same, but the continuous current rating falls from 400 mA to 260 mA because of the thermal path. A board running above 260 mA cannot take the TSSOP substitute, and the footprint differs in any case.
Does the enable pin work on both packages? The enable input is published on the LFCSP package. The TSSOP pinout does not carry it, so a board that relies on the enable line for power down isolation has to stay with the leadless part.