ADG1433YRUZ
Product Specifications
ADG1433YRUZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADG1433YRUZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADG1433YRUZ: three SPDT switches, 4.7 ohm, 115 mA per channel, break before make
The ADG1433YRUZ is the triple SPDT of the ADG1433/ADG1434 family: three independently selectable changeover switches on the iCMOS process, 4.7 ohm maximum on resistance at 25 C, 0.5 ohm flatness, up to 115 mA continuous current per channel, and an enable input that turns all three off. It is specified at plus or minus 15 V, +12 V and plus or minus 5 V.
Published values
| Parameter | Value |
|---|---|
| Configuration | three independently selectable SPDT switches |
| On resistance | 4.7 ohm maximum at 25 C |
| Flatness | 0.5 ohm |
| Continuous current | up to 115 mA per channel |
| Supply | plus or minus 15 V, +12 V or plus or minus 5 V |
| Switching | break before make |
| Package | 16-lead TSSOP or 4 mm x 4 mm LFCSP |
Three channels, one enable, one control word
Each of the three switches has its own control input, and the enable pin disables all of them at once. On a board that routes three signals between two paths, that is the minimum pin count for the job: three controls plus one enable, and no decoder to get wrong in firmware. The enable is also the power down isolation element, and it needs a pull resistor so that a reset does not leave a channel connected.
At 115 mA per channel the part carries real current. 4.7 ohm at 115 mA is 0.54 V and 62 mW per channel, so three channels at full current dissipate under 200 mW in a 16-lead package. That is inside the package rating but it is not nothing, and on a board with no airflow the copper around the pins is part of the thermal answer.
Break before make on a changeover switch
A changeover switch connects a common pole to one of two throws. If both throws are connected for even a few nanoseconds, the two sources are shorted together. The ADG1433 guarantees the break interval, so an unregulated source and a regulated one can be switched onto the same load without a cross conduction event, and a transducer drive can change direction without a current spike through two output stages.
The guarantee assumes the control signal is clean. A control line that crosses the logic threshold slowly, from an RC or a long cable, produces multiple transitions in one edge and repeated break make cycles. A Schmitt trigger buffer is the standard fix and costs less than the field failure it prevents.
Where it fits and what to watch
Relay replacement in instrumentation, audio and video routing, temperature measurement systems and avionics equipment that needs a wide analog range with no coil current. The 0.5 ohm flatness matters when the switch is in series with a signal whose amplitude carries information: flatness modulates the gain and shows up as distortion, while absolute resistance only shifts the level.
On a plus or minus 15 V rail the analog range is the full rail to rail span. On a single +12 V rail it is 0 V to 12 V, and a signal that swings below ground needs the dual supply configuration and a clamp at the connector to keep the pin inside the rails during power sequencing.
The pages that answer this most often are one stop BOM sourcing for the family alternatives, component lead time solutions for the acceptance test, and how to reduce component cost for the case where a replacement has to be fitted before the next build.
Two questions buyers ask
What is the difference between the ADG1433 and the ADG1434? Channel count. The ADG1433 has three SPDT switches in a 16-lead package, the ADG1434 has four in a 20-lead package. The switch itself, the 4.7 ohm maximum and the 115 mA rating are common to both.
Does the enable pin have to be used? It has to be at a defined logic level. Driving it high permanently is acceptable, leaving it floating is not: the state of all three switches becomes undefined and the power down isolation is lost.