ADG1408YCPZ
Product Specifications
ADG1408YCPZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADG1408YCPZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADG1408YCPZ: an 8 to 1 multiplexer with 4 ohm on resistance in a 4 mm LFCSP
The ADG1408YCPZ is the eight channel to one multiplexer of the ADG1408/ADG1409 family, in the 4 mm by 4 mm LFCSP. On resistance is 4 ohm typical and 4.7 ohm maximum at 25 C, flatness is 0.5 ohm, continuous current is up to 190 mA, and the part is fully specified at plus or minus 15 V, +12 V and plus or minus 5 V with 3 V compatible logic and break before make switching.
Published values
| Parameter | Value |
|---|---|
| Configuration | 8 single ended channels to 1 output |
| On resistance | 4 ohm typical, 4.7 ohm maximum at 25 C |
| Flatness | 0.5 ohm |
| Continuous current | up to 190 mA |
| Supply | plus or minus 15 V, +12 V or plus or minus 5 V |
| Switching | break before make |
| Logic | 3 V compatible, no VL supply required |
| Package | 4 mm x 4 mm LFCSP, 16 terminals |
Eight channels, three address lines, one converter
An eight channel front end that shares one converter saves seven amplifiers and seven converter channels, and the multiplexer is the whole of that saving. The cost is settling time: after the address changes, the source amplifier has to charge the switch capacitance, the track capacitance and the converter's sampling capacitor, through the 4 ohm switch and whatever series resistance protects the input.
With a 1 nF hold capacitor and 4 ohm of switch resistance the RC is 4 ns, so the settling is set almost entirely by the amplifier and by the charge the converter injects, not by the multiplexer. That is the opposite of a 120 ohm part, and it is why a low resistance multiplexer is chosen when the source is fast and the channel count is high.
Where the current rating is the point
At 190 mA through the 4.7 ohm maximum the drop is 0.89 V and the dissipation is 169 mW. A part rated for 190 mA can therefore switch a real load, such as a sensor excitation path or a redundant supply, and not only a high impedance input. The LFCSP helps here: the exposed pad is the thermal path, and on a board where the switch runs at 190 mA continuously the copper under the pad is doing as much work as the silicon.
Supply and signal range
On plus or minus 15 V the analog signal can swing to the rails and the switch passes a plus or minus 10 V signal without clipping. On a +12 V single supply the range is 0 V to 12 V. The 3 V logic threshold means a 3.3 V microcontroller drives the three address lines and the enable line directly, with no level shifter and no separate logic rail
The enable pin turns all eight channels off. On a multiplexer that shares a bus, that is the pin that isolates the board during power down, and it must be pulled to the off state so that a floating microcontroller pin during reset does not connect an unpowered channel to a live bus.
Where it fits
Multi channel data acquisition, relay replacement in instrumentation, audio and video routing in test equipment and temperature measurement systems that scan many sensors. The 0.5 ohm flatness is what keeps the channel to channel gain error small when eight different sensors share one converter.
Two pages worth reading before a purchase order goes out are one stop BOM sourcing and component lead time solutions; the first lists what else fits the socket, the second is the test sequence for a drop in, and medical device components covers the case where the shortage is already on the line.
Two questions buyers ask
What is the difference between the ADG1408 and the ADG1409? Channel count and configuration. The ADG1408 switches eight single ended channels with three address lines; the ADG1409 switches four differential pairs with two. They share the same 4 ohm switch and the same packages.
Can the multiplexer be used with a 3.3 V analog supply? Not in the specified range. The part is specified at plus or minus 5 V as its lowest rail, so a 3.3 V analog system needs a different family. The logic side can be 3 V, the analog side cannot.