Contact Us

ADCMP602BRMZ

Brand: Analog Devices
Analog Devices ADCMP602BRMZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADCMP602BRMZ — Analog & Mixed-Signal ICs | Superb Automation

ADCMP602BRMZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADCMP602BRMZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

ADCMP602BRMZ: 3.5 ns rail to rail comparator with latch and hysteresis

The ADCMP602BRMZ is a single comparator in an 8-lead MSOP built on a 2.5 V to 5.5 V single supply. It has a 3.5 ns propagation delay, a rail to rail input that accepts signals from 0.2 V below ground to 0.2 V above the positive rail, and a CMOS output stage that drives TTL levels. The 602 is the member of the family with both a latch input and a shutdown pin, and the hysteresis is programmed through the same pin as the latch.

Published values

ParameterValue
Propagation delay3.5 ns typical, 5 ns at 10 mV of overdrive
Supply range2.5 V to 5.5 V single supply
Supply current3 mA typical
Power dissipation10 mW at 3.3 V
Input common mode0.2 V below ground to 0.2 V above the positive rail
OutputCMOS and TTL compatible, low glitch
Hysteresis and latchprogrammed through a single pin
Shutdowndedicated pin on this order code
Power supply rejectiongreater than 50 dB
Temperature range-40 C to +125 C
Package8-lead MSOP
Replacement forMAX999, per the vendor

Two propagation numbers, two measurements

The 3.5 ns figure in the feature list is a small overdrive number and the 5 ns figure is quoted at 10 mV of overdrive. The difference is not a rounding error: a comparator slows down as the input approaches the threshold, and a 10 mV step is close enough to the decision point that the input stage has not fully slewed. A timing budget built on 3.5 ns has to assume 5 ns plus the dispersion the board adds, and a signal that arrives with 2 mV of overdrive is slower again.

For a 100 MHz clock, 3.5 ns is 35 percent of a period and 5 ns is half of one. That is the difference between a comparator that can slice a clock and one that can only detect a threshold, and it decides whether this part belongs in a data path or in a protection circuit.

The single pin hysteresis trick

Latch and hysteresis share a pin on the 602, and the way the pin is driven selects which function is active. A dc level programs a few millivolts of hysteresis, a pulse latches the output, and leaving the pin floating gives the comparator without either. That saves a package pin and a resistor, but it also means the pin cannot be left undriven by accident: a board that expects a latch and gets a floating pin gets neither function.

Hysteresis is what stops a slow moving input from producing a burst of edges at the output. A 60 Hz mains-derived signal with 10 mV of noise crossing the threshold will chatter without it, and the output stage will deliver a train of pulses to whatever counter follows.

Power and the output stage

3 mA at 3.3 V is 10 mW, which is low for a comparator with a 3.5 ns delay and is the reason the part is used in portable instruments and in multi-channel threshold arrays. The output stage is CMOS with a low glitch transition, so it does not put a current spike back into the supply every time it switches, which matters when eight of them share a rail.

An input range that goes 0.2 V beyond both rails means a signal that overshoots ground, as a current sense signal does on a switching edge, does not forward bias an internal diode. The 50 dB of supply rejection is the other half of that: a comparator that follows its own supply moves its threshold, and 50 dB turns a 100 mV supply step into 0.3 mV of threshold movement.

Two pages worth reading before a purchase order goes out are the amplifier cross reference and component lead time solutions; the first lists what else fits the socket, the second is the test sequence for a drop in, and how to verify a drop in replacement covers the case where the shortage is already on the line.

Two questions buyers ask

Is the ADCMP602BRMZ a drop in for a MAX999? The vendor calls it an improved replacement, and the function and the 8-lead MSOP body match. The pin functions of the latch and shutdown have to be checked against the MAX999 pinout before a board is released, because a replacement that fits the footprint can still invert a control.

How is the hysteresis set? By a dc level on the latch and hysteresis pin. A pulse on the same pin latches the output instead, so the two functions are exclusive and the driving circuit decides which one the comparator performs.